Bricks and Blocks

AAC and Lightweight Blocks vs Standard Concrete Blocks

How AAC and other lightweight blocks differ from standard concrete blocks in weight, strength, insulation and use, plus what to know about DIY polystyrene concrete.

On this page
  1. Quick comparison
  2. What AAC blocks are
  3. AAC vs standard concrete blocks
  4. Where AAC works, and where it does not
  5. Other lightweight blocks
  6. DIY polystyrene concrete blocks
  7. Can you use lightweight blocks as a foundation?
  8. Choosing

Quick comparison

AAC (autoclaved aerated concrete) blocks are much lighter than standard dense concrete blocks, cut easily with a hand saw, and insulate better. In exchange they are generally weaker in compression, more absorbent, and need more care around moisture and ground contact. Standard dense blocks are heavier and tougher, so they are the usual choice for foundations, retaining walls and exposed work.

What AAC blocks are

AAC is made from cement, lime, sand (or fly ash in some products), water and an expansion agent. The mix rises like a sponge, is cut into blocks, and is then cured in a pressurised steam chamber called an autoclave. The result is a material full of tiny air pockets. In the UK, AAC is often sold as “aircrete” or “thermalite” style blocks, and elsewhere as AAC or “Siporex”-type blocks.

AAC vs standard concrete blocks

AAC / aerated block Standard dense concrete block
Weight Much lighter, easy to lift Heavy, especially hollow 215 mm units
Cutting Hand saw, easy to chase and shape Needs a cutting tool or block splitter
Insulation Noticeably better thermal performance Lower, but good thermal mass
Compressive strength Lower, often 3.6 N/mm² class in the UK Higher, commonly 7 N/mm² or more
Moisture More absorbent, needs protection Also porous, but tougher outdoors
Mortar Often thin-bed adhesive, giving thin joints Conventional mortar
Typical use Inner leaves, partitions, upper storeys Foundations, party walls, retaining and exposed walls

Dense blocks in the UK commonly have a density of about 1,900 to 2,000 kg/m³ and lightweight aerated types around 1,100 kg/m³ or less, according to merchant data, though the exact figure depends on the product. Check the manufacturer’s data sheet.

Is AAC cheaper? It depends on the region and which dense block you compare. In some markets AAC costs more per block but saves on laying time, mortar and sometimes on structure weight. Get comparable quotes for a finished wall rather than comparing a single unit price.

Where AAC works, and where it does not

AAC is a good fit for:

  • Internal and non-load-bearing partitions
  • Inner leaves of cavity walls, where thermal performance matters
  • Upper storeys, where lower weight helps

Be cautious with AAC for:

  • Below-ground or ground-contact walls, unless the manufacturer specifically approves it
  • Exposed external walls, which normally need render or cladding to protect them from moisture
  • Garden walls, planters and retaining walls, where wet soil and frost are constant exposures

For these exposed jobs, see which concrete blocks to use for garden walls.

Other lightweight blocks

  • Lightweight aggregate blocks use expanded clay, pumice, ash or similar aggregates in place of dense gravel. They cut weight and improve insulation, but strength and density vary by product.
  • Foam concrete or cellular lightweight concrete (CLC) is made by mixing cement slurry with a pre-formed foam. It is sold as blocks or poured in place. It is similar in spirit to AAC but is cured without an autoclave, so properties differ between products.

DIY polystyrene concrete blocks

Polystyrene (EPS) concrete is a mix of cement, water and expanded polystyrene beads, sometimes with sand. The beads replace most of the heavy aggregate, so the finished block is very light and insulates somewhat better than ordinary concrete.

People make it at home for things like:

  • Lightweight garden ornaments and planters
  • Non-structural infill and insulating fill
  • Craft and model projects

Things to keep in mind before you try it:

  • Strength is low. Are foam and polystyrene concrete blocks strong? Strong enough for light, non-structural uses, but they are not equivalent to standard load-bearing blocks. Do not use home-made EPS blocks for load-bearing walls, foundations, retaining walls or anything with safety implications.
  • Mixes are inconsistent. Beads tend to float and segregate unless mixed carefully, so results vary batch to batch.
  • Fire and fumes. Polystyrene is a plastic and burns. Check local building rules before using it in a building.
  • Curing matters. Like any concrete, it needs to stay damp while it gains strength; see curing concrete.

If you want a light wall for a real building, a factory-made AAC or lightweight block with a known strength class is the safer route.

Can you use lightweight blocks as a foundation?

Generally no, unless the manufacturer and your design say so. Foundations and below-ground walls are normally built with dense blocks or poured concrete. If you are building a foundation or footing, follow the design from your engineer or building control and use blocks with the specified strength class. The UK strength classes are explained in what 7N means in concrete blocks.

Choosing

  • Need low weight and good insulation for an interior or protected wall: AAC or lightweight blocks.
  • Need strength, ground contact or exposure to weather: standard dense concrete blocks, or bricks. Compare them in brick vs concrete block: pros and cons.
  • Want to experiment at home: EPS concrete is fine for non-structural crafts, not for building walls.

The complete guide to bricks and blocks

Brick vs Concrete Block: Pros and Cons
Read the guide

Keep exploring

Guides from other topics

All topics →