Render, Screed and Finishes

Rendering and Plastering Walls: Mix Ratios, Application and Curing

A practical guide to cement render and plaster for brick walls: typical mix ratios by coat, sand choice, preparation, coat thickness and how long to cure.

On this page
  1. What rendering and plastering mean
  2. Typical mix ratios
  3. Measuring the parts, and what “1 bag of cement to sand” means
  4. Choosing sand
  5. Preparing a brick wall
  6. Applying the coats
  7. Curing: water curing of cement plaster
  8. Common problems
  9. Summary

What rendering and plastering mean

Rendering is applying a layer of cement-based mortar to a wall, most often an external one, to protect the masonry and give a uniform finish. Plastering usually means the same job done indoors. In some regions the words are used interchangeably, and a sand and cement coat applied to the inside of a brick wall is commonly called plaster. The materials and the method are very similar, so this guide covers both.

Render is normally built up in coats rather than applied in one go. A thin first coat gives grip, and one or two further coats bring the wall up to thickness and level.

Typical mix ratios

Mix ratios are given by volume, in the order cement : sand (sometimes cement : lime : sand). Exact recommendations vary between countries, standards and products, so treat the figures below as commonly used starting points rather than rules. If you are using a bagged, pre-blended render, follow the manufacturer’s instructions instead.

Coat Commonly used mix (cement : sand) Notes
First (scratch or base) coat about 1:3 to 1:4 Combed or scratched to give a key for the next coat
Second / finish coat about 1:4 to 1:6 Usually the same strength or weaker than the coat below
Cement : lime : sand often quoted around 1:1:6 Lime makes the mix more workable and a little more flexible

The principle worth remembering is that each coat should be no stronger than the one beneath it. A strong, rigid top coat over a weaker base tends to shrink more and crack or come away. Mixes that are very rich in cement look attractive on paper but shrink more as they dry.

Many people add a liquid plasticiser to improve workability instead of lime. Use a product made for the purpose and follow its dosage. For the same idea applied to floors, see sand and cement floor screed mix ratios.

Measuring the parts, and what “1 bag of cement to sand” means

The ratio refers to equal measures of volume, not weight. Use the same bucket, or a bottomless gauging box, for each part. A 1:4 mix is one bucket of cement to four buckets of sand.

If you are thinking in bags of cement, remember that a bag is a weight (often 25 kg or 50 kg depending on where you are). Sand is sold by weight or bulk volume, so it is easiest to scoop the cement and sand by bucket and not try to match a bag to a tonne of sand. Add water gradually until the mix is creamy and holds on the trowel without slumping.

If you want to estimate how much material a job needs, the coverage of a bag depends mostly on how thick you apply it. We explain the maths in how much a 20kg bag of render covers.

Choosing sand

Sand for render is usually a well-graded building or plastering sand, which is finer and gives a smoother, more workable mix than the coarse sharp sand used for screeds. Sand should be clean, with no clay, silt or salt. Dirty sand weakens the mix and can cause staining. Sand that is too fine can need more water and shrink more.

Preparing a brick wall

Preparation decides whether render stays on the wall.

Applying the coats

  1. First coat. Throw or trowel on a thin, even layer, pressing it into the surface. Comb or scratch it horizontally while it is still soft so the next coat has a key. Many guides suggest a coat of roughly 8 to 12 mm.
  2. Let it firm up. Wait until the first coat has set enough to resist a firm thumb press, which may be several hours to a day, depending on weather. Follow product guidance where available.
  3. Second coat. Apply the next layer, level it with a straight edge, and close the surface with a float. Total thickness for external render is often around 15 to 20 mm, and internal plaster is often thinner, but check the product or the local standard.
  4. Finish. Finish with a wooden or sponge float, or leave it textured, depending on the look you want.

Avoid rendering in direct sun, strong wind, rain or frost. Hot, windy conditions dry the surface too quickly, and frost can damage fresh render.

Curing: water curing of cement plaster

Cement needs water to harden properly. If render dries too fast, it can lose strength and develop cracks. Curing means keeping the work damp, shaded and protected while it gains strength.

Common practice is to start once the surface has set hard enough to survive misting without being marked, and then to mist it lightly with water a few times a day. Guidance for wall plastering commonly ranges from about 3 to 7 days, and some Indian site guidance quotes 7 days for wall plaster and floor screeds. In hot or windy weather, longer and more frequent curing is wise. Hanging damp hessian or plastic sheeting over the wall helps hold moisture in.

Note that “28 days” refers to the time at which concrete strength is normally tested, not to how long you need to water it.

Common problems

Summary

Use a mix that gets weaker, or at most the same strength, as you build outward, measure by volume with the same bucket, prepare and dampen the wall, apply thin coats, and keep the work damp for several days. When in doubt, follow the manufacturer’s data sheet or local standard.

Keep exploring

Guides from other topics

All topics →