Can you build a retaining wall yourself?
Yes, for the right wall. Low walls that hold back modest, well-drained soil are a common DIY project, especially when built from dry-stacked segmental blocks. A homeowner with patience, a plate compactor and a few helpers can do a good job. The risk rises quickly with height and load.
As a rough guide, many people treat walls of about 3 to 4 feet (roughly 1 metre) as the upper end of DIY. Above that, or whenever the wall holds back a slope, driveway, building or swimming pool, the forces are large enough that an engineer’s design is commonly required and is a sensible precaution even where it is not. Local rules differ, so check yours first (see permits and planning permission for retaining walls).
Planning before you dig
Work through these questions before buying material:
- How tall is the wall? Measure the height of ground you need to hold back, and add the buried part below ground when you plan the structure.
- What is behind it? Level lawn is a light load. A slope, a driveway, a shed or parked vehicles add surcharge, which makes the wall more demanding.
- What is the soil? Free-draining sand and gravel push less than heavy clay, which holds water and pushes harder.
- Where does the water go? Every wall needs a plan for drainage. See what to backfill behind a retaining wall.
- What is underground? Call your local utility locating service before digging.
- Do you need permission? Walls near boundaries, or above a certain height, often do.
Choosing a material
| Material | Typical DIY suitability | Notes |
|---|---|---|
| Segmental concrete blocks | Good for low to medium walls | Dry-stacked, no mortar, forgiving to build |
| Hollow concrete blocks (CMU) | Moderate | Needs a concrete footing, reinforcement and grout; see building with hollow concrete blocks |
| Brick | Moderate to hard | Needs skill and design; see brick retaining wall specifications |
| Poured concrete | Hard | Needs formwork, reinforcement and a lot of concrete; see formwork for a poured wall |
| Concrete sleepers | Moderate | Posts and panels; see concrete sleeper walls |
| Dry stone | Skilled, slow | See building a dry stone retaining wall |
| Gabions | Moderate | Wire baskets filled with stone; see gabion retaining walls |
Brick vs concrete retaining walls
Both can work well. Reinforced concrete, whether poured or built from grouted hollow blocks, is generally the stronger and more predictable choice for taller or heavily loaded walls because steel reinforcement carries the tension that masonry alone does not. Brick is attractive and durable but is usually used for lower walls, or for taller walls with a proper engineered design, because ordinary brickwork is weak in tension. Block is usually cheaper and faster to lay than brick, as each unit covers more area.
Which is “stronger” depends far more on design (thickness, reinforcement, footing, drainage) than on the material label. A well-designed brick wall beats a badly drained concrete one.
If cost drives your decision, see the cheapest retaining wall to build.
Footings, drainage and backfill basics
- Base: Segmental block walls usually sit on a compacted gravel base. Mortared masonry and poured walls need a concrete footing. Footings generally need to go below local frost depth in cold climates. For smaller walls, see whether a 2 foot wall needs a footing.
- Embedment: Part of the wall is buried. A commonly quoted guide is explained in the 1/3 rule for retaining walls.
- Drainage: Water trapped behind a wall is a leading cause of failure. Use clean granular backfill, a perforated drain pipe at the base that runs to an outlet, and weep holes in solid walls. Even low walls benefit; see drainage for a 600mm wall.
Working out concrete quantity
Concrete is ordered by volume. Multiply length × width × depth for each part, then add them together.
- Footing: length × footing width × footing thickness.
- Wall stem (if poured): length × thickness × height.
- Convert to cubic yards (divide cubic feet by 27) or cubic metres.
- Add roughly 5 to 10% for waste and uneven ground.
Worked example: a 20 ft long wall with a footing 2 ft wide and 8 in (0.67 ft) thick needs 20 × 2 × 0.67 ≈ 26.8 cubic feet, about 1 cubic yard. A stem 20 ft long, 8 in thick and 4 ft high adds 20 × 0.67 × 4 ≈ 53.3 cubic feet, about 2 cubic yards. With 10% extra, that totals around 3.5 cubic yards.
How many bags?
Bagged mix yields vary by brand, so check the bag. As a common rule of thumb, an 80 lb bag yields about 0.6 cubic feet, a 60 lb bag about 0.45 and a 50 lb bag about 0.37 cubic feet. That means a single cubic yard (27 cubic feet) takes around 45 bags of the 80 lb size. For anything beyond a small footing, ready-mix delivery is usually less work and gives more consistent concrete than hand mixing.
If you are building with hollow blocks, remember that cores filled with grout take extra volume too.
How thick does a concrete retaining wall need to be?
There is no single number. Thickness depends on height, soil, loads and reinforcement. Many small cantilever walls are in the range of 8 inches (200 mm) thick or more, with the base width often cited as roughly half to two thirds of the wall height. Treat those as rough starting points only and have anything tall or loaded designed by an engineer.
Common mistakes
- Skipping or shortcutting drainage.
- Using clay or topsoil as backfill against the wall.
- Footing too shallow for frost, or on soft or unprepared ground.
- Compacting heavily right against the wall face.
- Underestimating a slope or driveway above the wall.
- Starting without checking permit requirements.
Where to go next
Pick the type of wall you are leaning towards and read its detailed guide above. If in doubt about height, loads or soil, a short consultation with a local engineer or experienced mason costs little compared with rebuilding a failed wall.