Retaining Walls

Building Formwork for a Poured Concrete Wall

How to build strong formwork for a four-foot poured concrete wall: materials, bracing, ties, release agents and stripping, plus cheaper alternatives.

On this page
  1. What formwork has to do
  2. Planning a four foot wall
  3. Materials for the forms
  4. Building the forms
  5. Bracing and ties
  6. Can you use WD-40 as a release agent?
  7. Pouring and stripping
  8. Cheaper alternatives

What formwork has to do

Formwork is the temporary mould that holds wet concrete in shape until it hardens. For a four-foot wall it has to be straight, tight enough not to leak cement paste, and strong enough to resist the pressure of the wet concrete, which is surprisingly high. Wet concrete behaves much like a heavy liquid, and pressure increases with depth and with how fast you pour. Most formwork failures (“blowouts”) come from under-braced forms or pouring too quickly.

Planning a four foot wall

Before you build forms, settle the design:

Materials for the forms

  • Sheathing: Plywood designed for concrete forming (often called form-ply or similar), or sturdy exterior plywood. Thicker sheets resist bowing; ¾ inch is common.
  • Framing: 2×4s as studs and walers (horizontal stiffeners), commonly 2×4 doubled for walls this tall.
  • Ties: Snap ties, form ties or threaded rods with spreaders to hold the two faces together at the right thickness.
  • Bracing: Angled braces or stakes on the outside to hold the forms plumb.
  • Release agent: Form oil or a proper release product.
  • Screws, not nails, if you want to strip the forms without damaging them.

Commercial reusable form systems exist (aluminium, plastic or insulated forms) and make sense if you have a lot of wall to pour. For a single short wall, built-in-place plywood forms are usually cheaper. Flexible benderboard is made for curved edges or low pours, not for a four-foot wall.

Building the forms

  1. Prepare the footing. Make sure it is clean, cured and has its dowels in position.
  2. Set the rebar. Tie it to the dowels at the spacing in the design, with the correct cover to the face so it is not exposed.
  3. Build the panels. Screw plywood to studs spaced closely, at a spacing the designer or form supplier specifies, and add horizontal walers.
  4. Stand the first face and brace it. Check plumb in both directions.
  5. Install the ties, then stand the second face, so the distance between faces equals the wall thickness.
  6. Add spreaders or form ties to hold the spacing as concrete is placed.
  7. Seal the base and corners so slurry does not leak. Foam gasket or sealant helps.
  8. Check everything again immediately before the pour: plumb, straightness, level top, braces tight.

Bracing and ties

Concrete pressure is highest at the bottom of the form. Add more ties, closer stud spacing and extra walers at the bottom than the top. Do not rely on nails alone. Pour in lifts (layers) of a modest depth, vibrating or rodding each, and slow the pour rate on a tall form. If anything moves, stop and fix it before continuing. Wear eye protection, gloves and boots; wet concrete is caustic.

Can you use WD-40 as a release agent?

Many people do use WD-40 or cooking spray on forms, and it can work in a pinch. However, it is not designed for the purpose and can leave staining or affect the surface of the concrete. Dedicated form-release oils or agents are cheap and give more consistent results; they matter more if the wall face will be visible or painted. Test on a small area if you are using something unconventional. Apply any release agent thinly and keep it off the rebar, as it can reduce bond.

Pouring and stripping

Place concrete in layers, working it into corners and around rebar, tapping the form faces to release air. Leave the forms in place long enough for the concrete to gain strength; the usual guidance is at least a day or two for a wall, and longer in cold weather, but follow the mix supplier’s advice. Remove the ties and forms carefully so as not to chip edges. Keep the wall damp or covered while it cures. Do not backfill until the wall has gained enough strength per the designer, and compact backfill in thin layers.

Cheaper alternatives

The complete guide to retaining walls

How to Build a Retaining Wall Yourself: Materials and Planning
Read the guide

Keep exploring

Guides from other topics

All topics →