The short answer
There is no single “correct” mortar mix. The right ratio depends on how exposed the wall is, how strong and absorbent the bricks or blocks are, and what the wall has to carry. As a rough guide:
- UK general bricklaying and blockwork: around 1 part cement to 5 or 6 parts building sand, with a plasticiser added.
- Exposed, below damp-proof course or freestanding walls: a slightly stronger mix, often around 1:4 to 1:4½ with plasticiser.
- US bagged mortar: Type N for most above-ground walls, Type S where more strength is needed, such as below grade or in retaining walls.
Ratios below are given by volume, not weight, and are typical figures only. If you are building anything structural, check what your designer, building control or the product’s bag specifies.
What mortar is made of
Mortar is a mix of a binder, sand and water, often with an additive:
- Cement (Portland cement, or masonry cement in a pre-blended bag) is the binder that gives strength.
- Sand gives bulk and limits shrinkage. For bricklaying this is normally soft “building sand”, not sharp sand. See whether to use sharp sand or building sand for mortar.
- Water makes it workable and lets the cement set. Too much weakens it; see how to judge mortar consistency.
- Plasticiser or lime makes the mix creamier and easier to lay, and helps the mortar hold water against absorbent bricks.
So no, mortar is not “just sand and cement” in most professional mixes. Plain cement and sand does work, but it is harsher to lay, and it tends to be stronger and more rigid than the wall needs. For how mortar differs from concrete, see cement vs concrete vs mortar.
UK mixes for brickwork
In UK practice mixes are usually described as cement : sand, with a plasticiser assumed. The table is a commonly used guide, based on the traditional strength designations. Always check the product or specification for your job.
| Cement : sand (with plasticiser) | Typical use |
|---|---|
| 1 : 3 | Very strong; rarely needed on a domestic job |
| 1 : 4 to 1 : 4½ | Exposed or below-ground work, freestanding walls, engineering bricks |
| 1 : 5 to 1 : 6 | General above-ground brickwork and blockwork in sheltered or normal conditions |
| 1 : 7 to 1 : 8 | Lightly loaded internal walls only |
A stronger mortar is not automatically better. Mortar that is much harder than the bricks can push movement and stress into the bricks themselves rather than the joints. A mix in the 1:5 to 1:6 range suits most garden and house walls built with ordinary new bricks.
Mortar for blockwork
Blocks are usually laid with a mortar in the same range as for bricks, commonly around 1:5 or 1:6 cement to building sand with plasticiser. Because concrete blocks are larger, a bit drier and less absorbent than many bricks, the mix is often kept slightly stiffer.
That is why forum threads about block mortar contradict each other: some builders use 1:6 with plasticiser, others use a stronger 1:3 mix with no additive. Both can work; the stiffer, plasticiser-free mix is harder to lay and is less forgiving for a beginner. For blocks below ground or in a retaining structure, use the stronger end of the range. Joint thickness matters here too; see how thick mortar joints should be.
Plasticiser: how much and why
Plasticiser (an air-entraining additive) introduces tiny air bubbles that make the mortar smoother on the trowel, help it stick to the brick and improve frost resistance in the hardened joint.
- Follow the manufacturer’s dosing. It is normally given per bag of cement or per bucket of mix, and varies by product, so there is no universal figure.
- Measure it each batch. Inconsistent dosing changes the workability and the colour from one mix to the next.
- Don’t overdose. Too much air can weaken the mortar.
Why do bricklayers use washing-up liquid?
Some bricklayers have traditionally added a squirt of washing-up liquid for the same effect as a plasticiser. It is a quick fix, but the amount of air it entrains is unpredictable, so a proper plasticiser is the more reliable choice, particularly for a beginner or for work that matters structurally.
Lime in the mix
Traditional mixes use lime instead of a plasticiser, for example cement : lime : sand at 1 : 1 : 6. Lime improves workability and allows a little more flexibility, and is often preferred on older or softer masonry. If you are matching existing historic brickwork, a lime-based mortar may be the better choice, but get advice first.
US mortar types
In the US, mortar is classified as Types M, S, N, O and K under ASTM C270. The commonly quoted proportions by volume (cement : lime : sand) and minimum strengths are:
| Type | Cement : lime : sand | Minimum compressive strength (approx.) |
|---|---|---|
| M | 1 : ¼ : 3¾ | 2,500 psi |
| S | 1 : ½ : 4½ | 1,800 psi |
| N | 1 : 1 : 6 | 750 psi |
| O | 1 : 2 : 9 | 350 psi |
Type N is the usual all-round choice for above-ground work. Type S is a stronger choice below grade, for retaining walls and where there are higher wind or soil loads. Type O is a softer mortar often used for repointing and interior non-loading work. Our article on choosing between Type S and Type N mortar covers the decision in more detail.
Most DIY projects use pre-bagged mortar mix or masonry cement and sand, so you don’t have to measure the lime yourself.
How to mix masonry cement
Masonry cement is Portland cement pre-blended with plasticising and air-entraining ingredients. Mixing it usually only means adding sand and water, but the ratio is set by the manufacturer, so read the bag. A commonly seen instruction is about 3 parts sand to 1 part masonry cement by volume, but do not rely on that over the bag.
Whatever you are mixing:
- Measure sand and cement with the same bucket or shovel count each batch.
- Mix the dry materials until the colour is even before adding water.
- Add water gradually and mix until the mortar holds its shape on the trowel without slumping.
- Add plasticiser, if separate, with the water.
- Mix in small batches that you can use within a couple of hours, and do not re-wet mortar that has started to stiffen beyond a light re-tempering.
A mixer gives more consistent results than hand mixing on anything larger than a small repair.
How much cement do you need?
The simple method is:
- Work out the wall area in square metres.
- Multiply by the number of bricks or blocks per square metre.
- Estimate mortar volume, add an allowance for waste, then convert to cement using your mix ratio.
For the standard UK brick size (215 × 102.5 × 65 mm) with 10 mm joints, a single-skin wall uses about 59 bricks per square metre. The theoretical mortar volume works out at around 0.3 cubic metres per 1,000 bricks. In practice much is dropped or wasted, so planning on 25 to 30 percent more is sensible.
As a rough planning figure, a cubic metre of 1:5 mortar uses somewhere around 250 to 300 kg of cement. On that basis, 1,000 bricks may need roughly 4 to 5 bags of 25 kg cement, plus the sand and plasticiser. Treat this as an estimate and round up.
For 100 mm concrete blocks (440 × 215 mm face) laid with 10 mm joints, there are roughly 10 blocks per square metre, and the theoretical mortar is about 7 litres per square metre. As a rough example, 500 blocks cover about 50 square metres and may need about 4 or 5 bags of 25 kg cement at 1:5, again before generous allowance for waste. Bag sizes differ between countries (25 kg is common in the UK, 50 kg or 94 lb elsewhere), so calculate in kilograms, not bags.
Different mortar designs, joint thicknesses and wastage will change these figures. For a larger job, ask your supplier to help you quantify the order.
Common mistakes
- Mixing by the shovel rather than a measured container, so the ratio drifts.
- Using sharp sand for brick mortar, which gives a harsh, hard-to-lay mix.
- Making a mortar much stronger than the bricks, which can lead to cracked or spalled bricks over time.
- Adding too much water, which weakens the joint and stains the brick.
- Mixing more than you can use, then re-wetting stiffened mortar.
- Laying in frost or rapid drying conditions without protection; see how to cure brickwork.
For stonework, which has different needs, see mortar ratios for stone masonry.