Bricklaying and Mortar

Mortar Mix Ratio for Stone Masonry

What cement mortar ratio to use for stone walls: typical cement-to-sand mixes for rubble and dressed stone, Type N vs S, and when to use lime.

On this page
  1. The short answer
  2. Typical ratios by type of stonework
  3. US mortar types for stone
  4. Match the mortar to the stone
  5. Mixing and working tips
  6. How much mortar does stone use?

The short answer

For most stone walls built with cement mortar, a mix of around 1 part cement to 4 to 6 parts sand by volume is a typical starting point. The richer end (closer to 1:4) is used where the wall is exposed, retaining soil or carrying load. The leaner end (1:5 or 1:6) is common for sheltered garden walls and general rubble work.

These are common rules of thumb rather than fixed standards. If the wall is structural or retains soil, follow the design or local regulations.

Typical ratios by type of stonework

Stonework Commonly used cement : sand Notes
Random rubble garden wall 1 : 5 to 1 : 6 Workability matters; plasticiser helps
Rubble or coursed stone in an exposed or load-bearing wall 1 : 4 to 1 : 5 A richer mix gives more strength
Dressed or ashlar stone with thin joints 1 : 4 to 1 : 6 Finer sand gives cleaner joints
Retaining walls 1 : 4 or stronger Follow the design; drainage matters more than mortar

Note that retaining walls fail mostly through poor drainage and footings rather than the mortar mix. A stronger mortar will not compensate for water pressure behind the wall; see what to backfill behind a retaining wall for drainage.

US mortar types for stone

In the US, the mix is usually specified by mortar type rather than a simple ratio:

  • Type N (about 1 : 1 : 6 cement : lime : sand) is widely used for above-ground stone and stone veneer.
  • Type S (about 1 : ½ : 4½) is the stronger choice for below-grade walls, retaining walls and places with heavier loads or wind.
  • Type O is a softer mortar used on some interior work and soft historic stone repairs.

If you are choosing between the first two, our article on Type S versus Type N mortar explains the trade-offs. Pre-bagged Type N or S mortar mix is the simplest route for most DIYers.

Match the mortar to the stone

A basic principle of masonry is that the mortar should be softer and more porous than the masonry units, so that moisture and movement are taken by the joints rather than the stone. This matters most for:

  • Soft stones such as some limestones and sandstones, where hard cement mortar can cause the stone face to decay beside the joint.
  • Historic walls originally laid in lime mortar. Here a lime-based mortar is usually the better choice, and a conservation specialist can advise on the right mix.

For hard, dense stones such as granite, a cement mortar is generally fine.

Mixing and working tips

  • Use clean, well-graded building sand, not sharp sand; see sharp sand versus building sand.
  • Add a plasticiser or use lime to improve workability. Rough stone has an uneven bed, so the mortar must be creamy enough to fill voids.
  • Wet very dry or porous stone lightly before laying, so it does not draw water out of the mortar.
  • Keep joints to a width that suits the stone. Rubble work usually has wider and more irregular joints than brickwork, and this is not the same as brick joint thickness.
  • Protect new work from frost, rain and rapid drying; see how to cure masonry.

How much mortar does stone use?

Stonework uses much more mortar than brickwork for the same wall area, because of the irregular shapes and larger joints. The share of mortar in random rubble work is often estimated at roughly a third of the wall volume, but this varies a lot with the stone. Order generously and expect to round up.

For general mix definitions and more on proportions, see our main guide to mortar mix ratios for bricks and blocks.

The complete guide to bricklaying and mortar

Mortar Mix Ratios for Bricks and Blocks
Read the guide

Keep exploring

Guides from other topics

All topics →