What a brick bond is
A brick bond is the pattern in which bricks are arranged in a wall. The goal is to overlap the bricks so that vertical joints (perpends) in one course do not line up with those in the course below. Overlapping spreads loads across the wall and stops cracks from running straight down through a continuous joint. The pattern also sets the wall’s appearance.
Two terms help read any bond:
- A stretcher is a brick laid so its long side shows on the wall face.
- A header is a brick laid so its short end shows on the face.
A course is one horizontal layer of bricks.
The main types of brick bond
Stretcher bond
All bricks are laid as stretchers, with each course overlapping the one below by half a brick. It is the most common bond for modern half-brick (single-skin) walls and for the leaves of cavity walls. It is quick to lay and uses fewer bricks, but with a single skin it does not tie across the thickness of the wall, so cavity walls need wall ties.
Header bond
All bricks are laid as headers. This works for walls one brick thick, and is often used to build tight curves, because the short ends follow a radius more easily.
English bond
Alternate courses of stretchers and headers. The headers tie the wall together across its thickness, which makes English bond a strong choice for solid walls, retaining walls and load-bearing brickwork. It is the traditional bond for heavy engineering work.
Flemish bond
Each course alternates stretchers and headers along its length. It is often seen as more decorative than English bond, and it uses fewer whole bricks in some situations, but it needs more careful setting out. It is generally regarded as slightly less strong than English bond for heavy loads, though it is perfectly sound for normal walls.
English garden wall bond and Flemish garden wall bond
These are variations used for one-brick-thick freestanding garden walls. They use a run of stretchers (typically three) between each header in a course (English garden wall) or a mix of stretchers and a header in each course (Flemish garden wall). They use fewer headers than the full bonds, so are quicker and cheaper while remaining suitable for boundary walls.
Stack bond
Bricks are laid directly above one another so the vertical joints line up. It looks modern and clean, but there is no overlap, so it is structurally weaker. Stack bond walls typically need reinforcement, such as bed-joint reinforcing mesh, and the pattern is generally used for decoration, infill or non-structural panels rather than freestanding walls.
Others
You may also see Monk bond (usually two stretchers to one header in each course), Dutch bond and others. These are largely decorative variations.
Which brick bond is strongest?
For solid load-bearing walls, English bond is the answer most often given, because of the frequent headers tying the wall through its thickness. Flemish bond is close. Stack bond is the weakest because it lacks overlap. In a modern house, the strength of the wall in practice depends as much on the bricks, mortar and wall ties as on the bond. If you are building a structural wall, rely on the engineer’s specification rather than the pattern.
Mortar matters here; see mortar mix ratios for bricks and blocks.
The four types of masonry walls
Different sources list these differently, but a commonly cited set is:
- Solid walls, with units bonded through their thickness.
- Cavity walls, two separate leaves with an air gap, tied together with wall ties.
- Veneer walls, a non-structural masonry facing fixed to a backing structure.
- Reinforced masonry walls, with steel reinforcement in the joints or cores.
Load-bearing and non-load-bearing are other common ways to classify masonry walls.
Choosing a bond for your project
- Garden boundary wall, one brick thick: English garden wall or Flemish garden wall bond.
- Single-skin garden wall (half-brick): stretcher bond, normally with piers; see single-skin wall pier spacing.
- Cavity wall in a house or extension: stretcher bond in both leaves with wall ties.
- Retaining or heavy-duty solid wall: English bond, designed to the engineer’s requirements; see brick retaining wall specifications and design.
- Decorative panel: stack bond, with reinforcement as needed.
Whichever you choose, set it out dry before laying; the method is covered in how to lay the first course of bricks.