Bricks and Blocks

Brick vs Concrete Block: Pros and Cons

Compare bricks and concrete blocks on cost, speed, strength, appearance, insulation and moisture, plus how to choose for a DIY wall or building project.

On this page
  1. The short answer
  2. Brick vs concrete block at a glance
  3. Advantages of concrete blocks
  4. Disadvantages of concrete blocks
  5. Advantages of bricks
  6. Disadvantages of bricks
  7. Which is stronger?
  8. What does each cost?
  9. Using both together
  10. Which should you choose for a DIY project?

The short answer

Concrete blocks are larger, usually cheaper per square metre of wall, and much faster to lay. Bricks are smaller, easier to handle, and give an attractive finished face without needing render or paint. Neither is simply “better”. The right choice depends on whether the wall will be seen, what load it carries, and how much time and money you have.

This guide uses “brick” for a small fired-clay (or sometimes concrete) unit and “block” for a larger concrete masonry unit. Naming varies by region, so the details below are general guidance rather than a specification.

Brick vs concrete block at a glance

Brick Concrete block
Typical size Small, held in one hand Large, often needs two hands
Laying speed Slower, more joints Faster, fewer joints
Material cost per m² of wall Generally higher Generally lower
Finished look Attractive as laid Usually rendered, painted or clad
Handling Easy Heavy, especially dense or hollow units
Typical use Visible walls, facing leaves, paving Structural walls, foundations, inner leaves, retaining walls

Advantages of concrete blocks

  • Speed. One block covers the area of several bricks, so a wall goes up faster. In the UK, a standard 440 x 215 mm block lays to roughly 10 per square metre, compared with about 60 bricks for a half-brick-thick wall (see how many bricks you need per square metre).
  • Lower cost. Fewer units and less laying time usually mean lower material and labour cost for the same wall area. Prices vary a lot by region and supplier, so get current quotes.
  • Range of types. Blocks come in dense, medium and lightweight versions, in solid and hollow formats, and in different strength classes. Lightweight options are covered in AAC and lightweight blocks vs standard concrete blocks.
  • Reinforcement option. Hollow blocks can have their cores filled with concrete and steel to make a reinforced wall. See whether you need to fill hollow concrete blocks.
  • Thermal mass and sound. Dense blocks hold heat and block sound well.

Disadvantages of concrete blocks

  • Weight. Dense and hollow blocks are heavy, and repeated lifting is tiring for DIY builders.
  • Appearance. Plain blocks look utilitarian. Most are covered with render, paint, cladding or a brick skin.
  • Porosity. Standard blocks absorb water. Below-ground and exposed walls need suitable detailing, coatings or damp-proofing.
  • Cracking. Concrete shrinks as it cures and moves with temperature, so long walls generally need movement joints. Follow the guidance for your block type.
  • Less flexible for detail. Cutting blocks to fit curves, corners or small openings is harder than working with bricks.

Advantages of bricks

  • Appearance. Fired clay bricks have a natural colour that runs through the unit and usually ages well. They suit visible walls, garden features and house fronts.
  • Small units. Bricks are easy to lift, easy to cut, and good for curves, piers and detailed work.
  • Durability. Quality facing bricks, correctly chosen for the exposure, can last for generations. Engineering bricks are used where very high strength and low water absorption are needed.
  • Low maintenance. A brick face generally needs no painting or rendering.

Disadvantages of bricks

  • Slower to build. More units and more mortar joints mean more time per square metre.
  • Higher cost. Per square metre, brickwork is usually dearer than blockwork once materials and labour are counted.
  • Frost risk if the wrong type is used. Not every brick is suitable for exposed locations such as free-standing garden walls or the tops of walls. Check the manufacturer’s frost-resistance rating.
  • Variation. Colour and size can vary between batches, so it helps to buy enough from one batch for the whole job.
  • Red bricks specifically. Common red bricks can be soft, absorb water, and show salts (efflorescence) on the surface. Quality varies, so the details depend on the brand and grade.

Which is stronger?

It depends on the specific unit rather than the material. Compressive strength is quoted per unit, and ranges overlap. A dense structural concrete block can be stronger than a soft common brick, while an engineering brick is typically far stronger than ordinary blocks. Hollow blocks filled with reinforced concrete behave very differently from an unfilled wall.

For structural work, use the strength class on the plans or specified by your engineer. In the UK this is where labels such as 3.6N, 7N and 10N come in. We explain them in what 7N means in concrete blocks. For clay and concrete bricks specifically, see clay bricks vs concrete bricks.

What does each cost?

Prices for a thousand bricks or a pallet of blocks change with brand, region, type and delivery. Rather than rely on a number that goes out of date, get quotes from two or three local suppliers, and compare cost per square metre of finished wall, not cost per unit. Remember to include mortar, labour (or your own time), render or paint for blocks, and about 5 to 10 percent extra for cuts and breakages.

Using both together

Many houses use both. A common cavity wall has a brick outer leaf for appearance and a block inner leaf for speed, insulation and structure. In the UK, three block courses are designed to line up with nine brick courses, which makes tying the two leaves together straightforward. Garden walls often use a block core with a brick or stone face.

Which should you choose for a DIY project?

  • A plain wall that will be rendered, painted or hidden: blocks are usually the sensible choice.
  • A visible feature wall, pier or low garden wall: bricks give a better finish without extra coatings.
  • A retaining wall: use purpose-made retaining wall units or reinforced block, not decorative brick. See which concrete blocks to use for garden walls and how to build a concrete block retaining wall.
  • A load-bearing wall or anything with safety implications: ask a structural engineer or your local building control about requirements.

If you are unsure what an existing block is, see how to tell a cinder block from a concrete block. For planning your order, check standard brick sizes.

Keep exploring

Guides from other topics

All topics →