Retaining Walls

How to Build a Concrete Block Retaining Wall

Compare segmental retaining blocks, hollow concrete blocks and aerated blocks, then follow the main steps to build a concrete block retaining wall.

On this page
  1. Which type of block?
  2. Are cinder blocks good for a retaining wall?
  3. Planning and block count
  4. Building a segmental block wall
  5. Building with hollow concrete blocks
  6. Aerated concrete blocks
  7. Building on a slope
  8. Cost and lifespan
  9. Reusing retaining wall blocks

Which type of block?

“Concrete block retaining wall” can mean three quite different things:

  • Segmental retaining wall (SRW) blocks. Interlocking or pinned units designed for dry-stacking without mortar. They are the usual DIY choice for low and medium walls.
  • Hollow concrete blocks (CMU). Standard masonry units, laid in mortar on a concrete footing, with reinforcing bar in grouted cores. Stronger for taller walls when properly designed.
  • Aerated concrete (AAC) blocks. Lightweight, insulating blocks made for above-ground building walls. See below.

Are cinder blocks good for a retaining wall?

The term “cinder block” is often used loosely for any hollow concrete block. Older true cinder blocks were made with coal cinders and are weaker than modern concrete masonry units. Modern hollow concrete blocks can be used in a retaining wall, but only if they are laid on a proper footing, reinforced with steel and filled with grout. Empty, unreinforced hollow blocks stacked against soil are not a safe approach. Ask the supplier for the block’s compressive strength and use units intended for structural masonry.

Planning and block count

  • Check the height and load, and whether a permit or engineer is needed; see permits and planning permission.
  • Divide the wall face area by the face area of one block and add roughly 10% for cuts and breakage. A standard hollow block has a nominal face of 8 × 16 inches, so you need around 1.125 blocks per square foot of wall.
  • Order capstones separately.
  • Order drainage stone and fabric along with the blocks; see what to backfill behind a retaining wall.

Building a segmental block wall

  1. Mark the line and excavate. Dig a trench wide enough for the blocks plus working room behind. Depth must allow for the compacted base and for burying the first course (manufacturers typically specify the amount).
  2. Build the base. Lay compacted crushed stone, commonly around 6 inches thick for low walls, and make it dead level. Care here pays off at every course above.
  3. Set the first course. Use a long level and a string line. Bury it partly below grade as the manufacturer directs.
  4. Stack and offset. Run courses in a running bond so joints do not line up. Most systems step back slightly each course (setback) or use lips or pins to do so.
  5. Add drainage as you go. Place a perforated pipe at the base behind the wall, running to a daylight outlet, and fill behind the blocks with clean angular stone wrapped in non-woven fabric.
  6. Compact in thin lifts. Use a hand tamper close to the wall and a plate compactor farther back.
  7. Reinforce if specified. Taller walls often need geogrid layers. This is where design help is worth getting.
  8. Cap the wall. Fix capstones with a masonry adhesive intended for the purpose.

Building with hollow concrete blocks

  1. Pour a reinforced footing below frost depth and wide enough for the design. Dowel bars (rebar) project up where the cores will be.
  2. Let the footing cure before loading it.
  3. Lay the first course in a full mortar bed. Check level, line and plumb on every course.
  4. Lay the blocks in running bond, buttering the ends, keeping joints consistent, and threading vertical bars through the cores.
  5. Fill the cores with grout at the spacing the design calls for. For walls that retain soil, designs commonly specify grouted, reinforced cores.
  6. Provide drainage. Weep holes at the base plus a drain pipe and gravel behind the wall.
  7. Wait before backfilling. Mortar and grout need time to gain strength; many sources suggest at least a week or so. Follow the designer’s instruction.

Do cinder block walls need to be filled with concrete? For a retaining wall, generally yes: the cores are grouted and reinforced as the design specifies. Unfilled blocks are weak against lateral soil pressure.

Aerated concrete blocks

AAC blocks are light, easy to cut and good for insulation, which is why they are popular for house walls. They are not generally used as retaining walls. They are relatively soft and porous, absorb water, and are not designed to resist sustained soil pressure or constant ground moisture. If you want to use them in a below-ground or retaining situation, treat it as an engineered application and follow the manufacturer’s guidance. Whether AAC is cheaper than brick depends on region and project; the larger unit size does usually lay faster, but that does not make it the right product for holding back soil.

Building on a slope

A wall can be built on a slope by stepping the base. Each step is a level trench; the base is cut into level terraces, and the course above steps up. Keep the steps in whole-course increments so courses stay aligned.

Cost and lifespan

Retaining block prices vary a great deal by size, style and region, and installed prices are usually quoted per square foot of wall face. For budget comparisons see the cheapest retaining wall to build. A well-built, well-drained concrete block wall can last several decades; poor drainage and movement are the usual reasons for early failure.

Reusing retaining wall blocks

Segmental blocks can often be taken down and reused if they are undamaged. Clean off soil and old adhesive, check lips and pins for damage and sort them so you have a consistent set. Reuse works best when the blocks match, so keep spare blocks and be prepared to buy a few extras for the first course.

For a broader overview of all wall options, return to the DIY retaining wall planning guide.

The complete guide to retaining walls

How to Build a Retaining Wall Yourself: Materials and Planning
Read the guide

Keep exploring

Guides from other topics

All topics →