What a brick retaining wall is, and its limits
A brick retaining wall is a masonry wall built from fired clay or concrete bricks that holds back soil. Brick is strong in compression but weak in tension, and soil pushes a wall sideways, which tries to bend it. That is why brick retaining walls are usually limited to low heights unless they are thick, reinforced or built as part of a designed structure. Industry design guidance for brickwork retaining walls exists in most countries; for anything beyond a low garden wall, base the design on that guidance or on an engineer’s calculations.
Brick and mortar specification
- Bricks: Choose bricks rated for external use and for frost exposure where relevant. Look for products specified for use in retaining or below-ground conditions, which are typically dense, low-absorption, durable units. Soft, highly absorbent bricks tend to deteriorate when permanently damp. Ask the manufacturer or supplier to confirm suitability.
- Mortar: Use a mortar mix suited to the exposure and the brick. Strong, frost-resistant mortar is typical for retaining work; do not use weak or lime-heavy internal mixes. Mix proportions are specified by region and by the designer.
- Joints: Fill all joints fully, including the vertical (perpend) joints. Voids reduce strength and let water in.
Wall thickness and height
Thickness is the biggest design variable. A single-skin wall (one brick, about 4 inches or 102 mm thick) is generally suitable only for very low heights holding back light loads. Taller or more loaded walls are typically built two bricks thick or more, with piers, or as a cavity or reinforced-brick design. Thicker walls resist overturning better, but there is no universal chart: the right thickness depends on height, soil type, slope above the wall and surcharge.
When in doubt, keep it low, or get the design checked. For general height guidance and the permit side, see permits and planning permission for retaining walls.
Footing and foundation
Brick walls need a concrete footing, not just a compacted gravel base. The footing should:
- sit on firm, undisturbed ground;
- extend below frost depth in cold climates and below topsoil;
- be wider than the wall and thick enough to spread load. A commonly used starting point is a footing whose width is a few times the wall’s thickness, but this should be confirmed by a designer.
For small walls, see whether a 2 foot retaining wall needs a footing. Poured footings need formwork; see building formwork.
Reinforcement and piers
Taller brick walls typically use steel reinforcement, in bed-joint reinforcement or in grouted cavities, and piers or buttresses to resist lateral pressure. In some designs, a brick facing is applied to a reinforced concrete or block wall, in which case the structure behind does the retaining and the brick is cosmetic. For a retaining structure behind a brick face, see building with concrete blocks.
Drainage, waterproofing and detailing
How to detail a brick wall for a retaining condition:
- Drainage: Granular backfill and a perforated drain pipe at the base, discharging to an outlet.
- Weep holes: Gaps left in the bottom course of the vertical joints, or pipes through the wall, so water can escape. Spacing is commonly specified by the designer, often around every 1 m or a few feet.
- Damp-proofing: Apply a bitumen or similar waterproof coating to the soil face to reduce moisture reaching the brick, and consider a damp-proof course near ground level to stop moisture rising into the visible wall.
- Movement joints: Long runs of brick expand and contract, and movement joints at intervals are commonly specified; the spacing depends on the brick and the region.
- Coping: A cap or coping with a drip detail sheds water off the top.
- Backfill: Use granular material; see what to backfill behind a retaining wall. For low walls, see whether a 600mm wall needs drainage.
Typical brick dimensions
Sizes vary by country. In the UK a standard metric brick is about 215 × 102.5 × 65 mm, which gives a work size of roughly 225 × 112.5 × 75 mm with joints. US modular bricks are typically around 7⅝ × 2¼ × 3⅝ inches. A typical single-skin wall is thus about 4 inches thick, a double-skin wall roughly 8 to 9 inches. Check actual dimensions with your supplier before calculating quantities.
Which blocks for a retaining wall?
If you want something less labour-intensive than brick, consider segmental retaining blocks for dry-stack walls, or hollow concrete blocks with grout and rebar for taller reinforced walls. Both are covered in our concrete block retaining wall guide, and the trade-offs between brick and other materials are summarised in the DIY retaining wall planning guide.
Cost note
Brick tends to cost more per square foot than block because laying takes longer and the material is more expensive. Compare options in the cheapest retaining wall to build.