Retaining Walls

What to Backfill Behind a Retaining Wall: Gravel, Fabric and Compaction

Use clean angular gravel, filter fabric and a perforated drain pipe behind a retaining wall. Learn what backfill to use, what to avoid and how to compact it.

On this page
  1. Short answer
  2. Why backfill matters
  3. The drainage zone: clean angular stone
  4. Filter fabric
  5. The drain pipe
  6. Backfill beyond the stone
  7. What not to use
  8. Compaction
  9. Finishing the top
  10. Common mistakes

Short answer

Behind a retaining wall, use clean, free-draining, angular crushed stone directly against the wall, separated from the native soil by non-woven filter fabric, with a perforated drain pipe at the base that runs to an outlet. Further back, use granular fill that drains and compacts well. Avoid clay, topsoil and organic material against the wall.

Why backfill matters

The soil and stone behind a wall carry the load the wall has to resist. Wet, heavy or poorly drained fill pushes much harder than dry granular fill, and water trapped behind a wall is among the most common causes of leaning, bulging and failure. The job of the backfill is to let water escape and to keep the pressure on the wall predictable.

The drainage zone: clean angular stone

  • Stone type. Clean, angular crushed stone with few fines is the usual specification. A commonly quoted size range is about ¾ to 1½ inches (roughly 20 to 40 mm), sometimes described as “clean crushed stone” or “drainage aggregate.” Angular pieces lock together and keep voids open.
  • Width. A commonly recommended drainage zone is at least around 12 inches (300 mm) wide behind the wall, and wider for tall walls or wet sites. Segmental block manufacturers typically give their own figure.
  • Height. It should run the full height of the wall, or close to it.
  • Why not pea gravel or sand? Rounded pea gravel does not lock together and can shift, and sand and soil can clog the voids. Crusher run with lots of fines can hold water.

Filter fabric

Wrap the drainage stone with a non-woven geotextile placed between the stone and the native soil. This stops fine soil from washing into the gravel and clogging it over time. Overlap the seams, and fold the fabric over the top of the stone before covering with soil. Do not put fabric directly between the stone and the back of the wall unless the system requires it, as the drainage zone should connect to the wall’s joints or weep holes. Woven landscape fabrics can clog; check the product is a drainage geotextile.

The drain pipe

  • Lay a 4-inch perforated pipe at the base behind the wall, commonly in a bed of the same drainage stone, with perforations oriented as the manufacturer directs.
  • Give it a steady fall toward an outlet, often quoted as about 1% (roughly 1 inch per 8 feet), and carry it to daylight, a suitable soakaway or a drainage point where water can leave.
  • Protect the outlet from blockage with a screen, and keep it clear.
  • Leave the pipe accessible, if possible, for cleaning.

Even short walls benefit from this; see whether a 600mm retaining wall needs drainage.

Backfill beyond the stone

Behind the drainage zone, use the best soil you have available:

  • Granular, free-draining material, such as a sandy or gravelly soil, is preferred.
  • If your native soil is clay, remove as much as is reasonable from the zone immediately behind the wall, or limit the fill to a good drainage zone and cap it with clay to shed water.
  • Order a little extra, since compaction reduces volume, with allowances of around 15 to 20% sometimes suggested.

What not to use

  • Clay or heavy, wet soil directly against the wall.
  • Topsoil and organic material, which compress and hold water.
  • Construction rubble, concrete with lots of fines or anything that could clog or settle.
  • Sand alone behind a wall that should drain.

Compaction

  1. Place backfill in thin layers, commonly around 6 to 8 inches (150 to 200 mm) before compacting.
  2. Use a hand tamper or small plate compactor. Keep heavy equipment well back from the wall. A heavy compactor right against the face can push segmental blocks out of line or overload the wall.
  3. Compact the drainage stone lightly; it needs less than soil, but should not be left loose.
  4. On mortared or poured walls, wait until the wall has gained enough strength before backfilling, commonly at least about a week, or as the designer specifies. For segmental dry-stack walls, backfilling can proceed as the wall is built, course by course.
  5. Where reinforcement such as geogrid is part of the design, follow the layers and lengths it specifies.

Finishing the top

Cap the backfill with soil or paving that slopes away from the wall, so surface water runs off rather than soaking in. Consider an impermeable cap or a swale if a lot of water arrives from above. Do not bury the outlet or let landscaping block it.

Common mistakes

  • Using soil instead of gravel behind the wall.
  • No filter fabric, so the drainage clogs.
  • A pipe with no fall or no outlet.
  • Compacting too thickly or too close with heavy equipment.
  • Backfilling a mortared wall too early.
  • Forgetting to make a plan for surface water.

For wall-type guidance, see concrete block walls, gabion walls, and the overall DIY retaining wall guide.

The complete guide to retaining walls

How to Build a Retaining Wall Yourself: Materials and Planning
Read the guide

Keep exploring

Guides from other topics

All topics →