Retaining Walls

How to Build a Dry Stone Retaining Wall Step by Step

Build a low dry stone retaining wall without mortar: choosing stone, laying the base, using batter and through stones, and handling drainage.

On this page
  1. What a dry stone retaining wall is
  2. Before you start
  3. Tools and materials
  4. Step by step
  5. Principles of good dry stone work
  6. Drainage and backfill
  7. Common mistakes
  8. When to choose another wall

What a dry stone retaining wall is

A dry stone retaining wall is built from stone fitted together without mortar (for mortared stonework, see mortar mix ratio for stone masonry). It stays up through the weight and interlock of the stones and by leaning back (batter) into the bank it holds. Because there is no mortar, water passes through easily, which helps drainage, and the wall can flex slightly with ground movement. Well-built dry stone walls can last a very long time, but the craft takes practice and the work is slow and heavy.

Before you start

  • Keep it low. Dry stone retaining walls are best suited to modest heights, with larger walls typically needing a skilled waller or an engineered design. Do not build one against a building, driveway or steep slope without professional advice.
  • Check the rules. Some places require approval for walls above a certain height or near boundaries; see permits and planning permission.
  • Choose suitable stone. Hard, durable stone that splits or sits in blocky shapes works best. Rounded stones are harder to stabilise. Ideally, you have a mix of large foundation stones, medium face stones, long “through” stones and small fillers.

Tools and materials

  • Stone, sorted by size and shape
  • Spade, rake and wheelbarrow
  • Tamper or compactor for the base
  • String line, stakes and a level
  • A template or A-frame to check the batter
  • Hammer and chisel for shaping, with eye protection and gloves
  • Drainage stone and non-woven geotextile for behind the wall

Stone is heavy. Use proper lifting technique, steel-toe boots and a plan for moving large pieces, such as planks, a trolley or a lifting aid.

Step by step

  1. Set out the wall. Mark the front line with stakes and string. Plan the width at the base to be generous; dry stone walls are usually thicker at the bottom than the top.
  2. Excavate the foundation. Dig a trench into firm ground and slope the base slightly back into the bank, rather than perfectly level, so the courses tilt inwards. Remove roots and soft soil.
  3. Compact a base. Add and tamp a layer of crushed stone to give a firm, even bed.
  4. Lay the foundation course. Use the largest, flattest stones, set with their long side running into the bank. Make sure each is stable and does not rock.
  5. Build the face and the “hearting.” Build the front face and back face of the wall together, and fill between them with small stone (“hearting”), packed tightly. Loose hearting makes the wall weak.
  6. Follow the rules of bonding. See below.
  7. Add through stones. At intervals, place long stones that span the full width of the wall, tying front to back.
  8. Add drainage as you go. Place free-draining stone behind the wall. See below.
  9. Finish with cope stones (capping), set on edge or flat, heavy enough to lock the top.

Principles of good dry stone work

  • One over two, two over one. Each stone should bridge the joint between the two stones below it, so vertical joints do not line up.
  • Batter. The face leans back into the bank. A common approach is to check the angle with a template as you build, with the amount depending on the stone and wall height.
  • Through stones. Tie the two faces together at regular intervals, often about halfway up and near the top.
  • Stable stones. Each stone is wedged with small pieces (pinnings) so it cannot rock.
  • Long edge into the wall. Place long stones lengthways into the wall, not along the face, to give depth and strength.
  • Heavy at the bottom. Reserve the biggest stones for the base.

Drainage and backfill

The joints of a dry stone wall let water through, but backfill behind it still matters. Use clean, free-draining angular stone directly behind the wall and, where the soil would wash through the gaps, a layer of non-woven fabric between the stone and the soil. Do not use clay against the back. See what to backfill behind a retaining wall and drainage on low walls.

Common mistakes

  • Building vertically instead of battered.
  • Skipping through stones.
  • Filling the middle with soil or loose rubble.
  • Using rounded or weathered stone with little interlock.
  • Building too high for the stone and base.
  • Building without a firm base.

When to choose another wall

If you lack suitable stone or want a faster build, consider segmental block walls or gabion baskets, which use stone fill in a more forgiving way. For a general overview, see the DIY retaining wall guide.

The complete guide to retaining walls

How to Build a Retaining Wall Yourself: Materials and Planning
Read the guide

Keep exploring

Guides from other topics

All topics →