Short answer
For fence posts and small garden footings, a commonly used mix is about 1 part cement to 5 or 6 parts all-in ballast by volume. If you mix your own sand and coarse aggregate, the classic 1 : 2 : 4 (cement : sand : aggregate) serves the same purpose. Some suppliers suggest a simpler blend of roughly one part sand to four parts ballast with cement added. Recommendations vary, and bagged post-mix products with their own instructions are often easier.
For house foundations, do not rely on a general ratio. The mix is normally specified by the designer or building control, and is usually ordered as ready-mix.
For more background on ratios, see our guide to concrete mix ratios.
Fence posts: mix, hole size and quantity
Common rules of thumb for post holes are:
- Depth: roughly one-third to one-half of the post’s above-ground height, and deeper where the frost line is deep or the ground is soft.
- Width: about three times the width of the post, giving a collar of concrete on all sides.
- Base: some people add a few centimetres of gravel under the post for drainage.
Concrete holds a post firmly, but it can trap water against timber. Use a post that is suitably treated, and slope the concrete top away from the post so water runs off.
Worked example
Say you have a 100 mm (4 in) square post, a hole about 300 mm square and 600 mm deep.
- Hole volume: 0.3 × 0.3 × 0.6 = 0.054 m³.
- Post volume in the hole: 0.1 × 0.1 × 0.6 = 0.006 m³.
- Concrete needed: about 0.048 m³ per post, before any allowance for waste.
Allow roughly 10% extra. For ten posts, that is a little over half a cubic metre. To turn that into materials, see how to calculate how much concrete you need, and for ballast-based quantities see how much cement you need for 1 tonne of ballast.
If you use bagged mix, check the yield on the bag. For example, an 80 lb bag typically yields about 0.6 cubic feet and a 60 lb bag about 0.45 cubic feet, though products differ.
Is 2 ft deep enough for fence posts?
For a fence about 6 ft tall, burying roughly 2 ft is a common guideline, following the one-third rule. Two feet can be enough for a standard fence in firm ground, but you may need more depth if:
- the ground is soft or sandy;
- you are in an area with deep frost;
- the fence is exposed to strong wind or carries solid panels;
- the post supports a gate.
Local guidance and the fence manufacturer’s instructions should be your reference.
Garden and small-building footings
For garden walls, sheds and similar light structures, a general-purpose ballast mix of around 1 : 5 or 1 : 6 is commonly used for unreinforced footings. Heavier loads, poor ground or reinforced footings call for a stronger, specified mix. For sizing a wall footing, see how deep a footing should be for a brick wall, and for a shed slab, whether 4 inches of concrete is enough for a shed base. Ready-mix suppliers can recommend a designation for your project; see concrete grades M25, M30 and RC30 for how those designations work.
House foundations: what to follow
For the foundations of a house or extension, the required concrete strength, width and depth depend on the ground conditions and the load. In many places, this is checked by building control or a structural engineer. Use the mix on the approved drawings, and do not substitute a bucket ratio. Ordering ready-mix concrete is the usual route because it arrives with a known specification.
Foundation thickness
The thickness of a foundation depends on the design, soil and loads. Simple strip foundations for low-rise domestic work are often in the region of 150 mm or more in thickness, with depth to suit the ground, but many designs are deeper or thicker. Treat any single figure as indicative and follow the approved plans.
Concrete versus mortar in foundations
Foundations use concrete, which contains coarse aggregate for strength. Mortar (cement, fine sand and often lime or plasticiser) is meant for bedding and joining bricks and blocks, not for pouring foundations. Mortar mixes are typically in the range of 1 : 4 to 1 : 6 cement to sand, depending on the job. See cement vs concrete vs mortar for the differences.
Tips
- Mix to a stiff but workable consistency; see how much water to add to concrete.
- Fill the hole in layers and work the concrete to remove air pockets.
- Brace posts plumb until the concrete has set.
- Keep fresh concrete damp and protected from frost during curing.