Concrete Mix Ratios

How to Mix Concrete by Hand Without a Mixer

A step-by-step guide to mixing concrete by hand in a wheelbarrow or on a board, with tools, safety, batch sizes, water control and common mistakes.

On this page
  1. What you need
  2. Safety
  3. Step-by-step in a wheelbarrow
  4. Mixing from separate ingredients
  5. Batch size and timing
  6. Common mistakes
  7. When to use a mixer
  8. Clean-up

What you need

  • A sturdy wheelbarrow, mixing tub or a flat, clean board or sheet
  • A mortar hoe, garden hoe or a square-edged shovel
  • A bucket or container for measuring water, and one for dry ingredients if mixing from scratch
  • Bagged concrete mix, or cement plus sand and aggregate (or ballast)
  • Clean water
  • Gloves, eye protection and a dust mask

Safety

Wet cement is alkaline and can burn skin, so wear waterproof gloves and wash off splashes promptly. Dry cement dust can irritate the eyes and lungs, and concrete mixes contain silica, so wear a dust mask and avoid raising dust. If concrete gets in your eyes, rinse with plenty of water and seek medical advice. Wear sturdy boots and long sleeves, and take care of your back when lifting bags.

Step-by-step in a wheelbarrow

  1. Load the dry mix. Empty your measured bagged mix into the wheelbarrow. If you are working from separate ingredients, mix them dry first until the colour is even.
  2. Make a well or divide the space. Form a hollow in the centre of the dry pile, or push the dry mix to one side of the barrow.
  3. Add most of the water. Measure the water recommended for the amount you are mixing, and pour roughly two-thirds to three-quarters of it into the hollow.
  4. Fold and mix. Pull dry material from the edges into the water with the hoe or shovel. Scrape the bottom and corners so that no dry pockets stay trapped underneath.
  5. Add the rest gradually. Add the remaining water a little at a time until no dry powder remains. Stop as soon as the mix is right, because extra water weakens the finished concrete (see how much water to add to concrete).
  6. Check consistency. The mix should look like thick oatmeal or peanut butter and hold its shape without turning into a puddle.
  7. Place it promptly. Move the mix into the formwork or hole right away, before it begins to stiffen.

Mixing from separate ingredients

If you are not using a bagged mix, measure by volume with the same container every time, using ratios such as 1 : 2 : 4 (cement : sand : aggregate) or about 1 : 5 cement to ballast. See our guide to concrete mix ratios for options.

On a board or flat surface, mix the dry sand and cement first until the colour is uniform, add the aggregate, and turn the heap over a few times. Then form a crater, pour in some water and fold the dry material in from the edges.

Batch size and timing

Keep batches small. For a wheelbarrow, one to two bags of bagged mix, or the equivalent, is about right for most people. Larger batches are hard to mix thoroughly by hand, and concrete begins to set after a limited working time, so prepare the formwork, tools and a helper before you add the water.

For estimating how many batches you need, see how to calculate how much concrete you need.

Common mistakes

  • Pouring all of the water in at once, which makes dry pockets and soup at the same time.
  • Skipping the dry mix step with separate ingredients, which results in uneven strength.
  • Leaving unmixed material in the corners of the wheelbarrow.
  • Using too much water because it is easier to move around.
  • Mixing a batch that is too large to place before it begins to set.

When to use a mixer

For anything beyond small jobs, such as a slab, a long footing or multiple fence posts, a powered mixer saves effort and gives a more consistent result. Mixers can be hired by the day from most tool-hire shops. If you are weighing up the options, see whether it is cheaper to mix your own concrete or buy bags. For a thin, appearance-critical piece such as a worktop, consistency is even more important; see concrete countertop and worktop mix ratios.

Clean-up

Wash the wheelbarrow and tools straight away, before the residue hardens. Do not pour wash water into drains or watercourses; follow local rules on disposing of cement slurry.

The complete guide to concrete mix ratios

Concrete Mix Ratios: Cement, Sand, Ballast and Water Explained
Read the guide

Keep exploring

Guides from other topics

All topics →