Concrete Slabs

Do You Need Rebar or Wire Mesh in a Concrete Slab?

Learn what rebar and wire mesh do in a concrete slab, when they are worth using, how to place them correctly, and when light-duty slabs can go without.

On this page
  1. Short answer
  2. What reinforcement does and doesn’t do
  3. When you probably need it
  4. When you can often skip it
  5. Mesh, rebar or fibres
  6. Placement matters
  7. What’s the cheapest way to reinforce?

Short answer

It depends on what the slab does. Light-duty slabs on firm, well-prepared ground, such as a small garden path or shed base, are often laid without reinforcement, relying on a good base and properly placed joints. Slabs that carry vehicles, are large, sit on less reliable ground, or are poured in sections more often use welded wire mesh or rebar. When in doubt, reinforcement is a modest extra cost for added insurance, but it has to be positioned correctly to do any good. For structural slabs, follow the engineer’s design.

What reinforcement does and doesn’t do

Concrete is strong in compression and weak in tension. Steel takes the tension. In a ground-bearing slab, though, reinforcement mostly does a different job: it holds cracks tightly together so they stay narrow. It does not stop concrete from cracking, and it doesn’t make up for a poor base, too much water in the mix, or missing joints.

Reinforcement can also help:

  • Keep slab sections tied together across joints.
  • Spread loads where the ground is slightly uneven.
  • Reduce the risk of one side of a crack moving up or down.

When you probably need it

  • Driveways and garage floors, where vehicles apply repeated loads.
  • Slabs on soft or variable ground, or where some settlement is possible.
  • Larger slabs and thicker slabs with more demanding use.
  • Where slabs are joined with construction joints or poured in sections; see how to lay a concrete slab.
  • Anything structural, such as a slab supporting walls or a suspended floor. See types of reinforced concrete slabs.

When you can often skip it

For a 4-inch (100 mm) slab, many builders still add mesh if it carries vehicles; for pedestrian-only use, it is optional. Check local building guidance if the slab relates to a building or regulated work.

Mesh, rebar or fibres

  • Welded wire mesh comes in flat sheets and is quick to lay. In the UK, A142 mesh (6 mm wires at 200 mm spacing) is a common choice for domestic slabs and driveways, with heavier meshes such as A193 for greater loads. In the US, 6×6 welded wire mesh is often mentioned for similar jobs.
  • Rebar (reinforcing bar) is laid in a grid, commonly 10–12 mm bars (about 3/8–1/2 in) at spacings of a few hundred mm, tied at crossings. It is stiffer and generally used for heavier-duty slabs or where thickened edges and beams are needed.
  • Fibres (steel or synthetic) are added to the mix and help control shrinkage cracking. They are not usually a direct substitute for mesh or bar where the design calls for steel.

Exact sizes depend on the design load, so treat these as examples only.

Placement matters

Reinforcement only works if it sits at the correct depth and is held there.

  • Support it on spacers (chairs) so it sits in the upper half of the slab, with cover of roughly 40–50 mm from the surface for external slabs. Don’t leave it lying on the ground.
  • Lap sheets of mesh by at least one or two squares, and tie them, so they behave as one.
  • Keep steel away from the formwork edges so it is covered by concrete and protected from corrosion.
  • Don’t walk mesh down into the concrete after pouring, as it tends to end up in the wrong place.
  • Cut the mesh at joints that are meant to open, or follow your design for dowels and ties; see control joint spacing in concrete slabs.

What’s the cheapest way to reinforce?

For most DIY slabs, mesh sheets on spacers are the simplest and cheapest practical option. Fibres can be cost-effective for crack control but serve a different purpose. Cheaper isn’t better if it doesn’t match the load, so choose the reinforcement for the job, and keep the base, mix and curing right as well. See curing concrete.

The complete guide to concrete slabs

How to Lay a Concrete Slab: Base, Mix and Pouring in Sections
Read the guide

Keep exploring

Guides from other topics

All topics →