Concrete Slabs

Types of Reinforced Concrete Slabs

An overview of reinforced concrete slab types, from ground-bearing and raft slabs to one-way, two-way, ribbed and post-tensioned, with notes on grades and reinforcement.

On this page
  1. Quick overview
  2. Ground-bearing slabs and foundation slabs
  3. Suspended slabs
  4. Post-tensioned and precast slabs
  5. PCC versus RCC
  6. Concrete strength grades
  7. What is the cheapest way to reinforce concrete?
  8. Which type matters for a DIY project?

“Concrete slab” covers a surprisingly wide range of things, from a garden path poured on the ground to a multi-storey floor spanning between columns. Reinforced slabs add steel (or sometimes fibres) to deal with the tension that concrete handles poorly. This overview lists the main types, so you know which one you are dealing with. It is general information, not a design guide; structural slabs should be designed by a qualified engineer.

Quick overview

Slabs fall into two broad families:

  1. Ground-bearing slabs, which rest directly on a prepared base of soil or stone.
  2. Suspended (elevated) slabs, which span between supports such as walls, beams or columns.

Within each family there are many variations, depending on span, loading and how the slab is reinforced.

Ground-bearing slabs and foundation slabs

Slab-on-grade (ground-bearing slab). The slab sits on a compacted base, and the ground carries most of the load. This is what most DIY projects involve: paths, patios, shed bases, garage floors and driveways. Reinforcement, where used, is typically light mesh to control cracking rather than to span any distance. See how to lay a concrete slab and rebar or wire mesh in a concrete slab.

Raft foundation. A thicker, reinforced slab, often with thickened edges or ribs, that spreads a building’s load over a large area. It is commonly considered where ground is weak or variable, and it needs engineered design.

Strip or pad foundations with a slab. Here, the walls sit on separate footings, and a floor slab is cast within them. The floor slab may be ground-bearing or suspended.

When people ask about “types of concrete slab foundations,” they are usually asking about these options: slab-on-grade, raft (including stiffened or ribbed rafts), and suspended or beam-and-block floors.

Suspended slabs

One-way slab. Supported on two opposite sides, so the main reinforcement runs in one direction, spanning between the supports. A common rule of thumb is that a slab is treated as one-way when its long side is more than about twice its short side.

Two-way slab. Supported on all four sides (typically by walls or beams) and bending in both directions, so main reinforcement runs both ways. It is generally used where the slab is closer to square.

Flat slab and flat plate. A slab supported directly on columns with no beams below. Flat slabs may have thickened areas (drop panels) or column heads to handle punching shear at the columns.

Ribbed slab. A slab with a series of ribs (small beams) underneath and thin concrete between them, saving material and weight.

Waffle slab. A two-way version of the ribbed slab with ribs in both directions, producing a grid pattern underneath. It can span relatively long distances for its weight.

Composite slab. Concrete cast on profiled steel decking, which acts as formwork and often as reinforcement.

Post-tensioned and precast slabs

Post-tensioned slab. Steel tendons run through the slab and are tensioned after the concrete has gained strength, putting the concrete into compression. This allows thinner slabs and longer spans. It is specialist work and not a DIY technique.

Precast slabs. Hollow-core planks, beam-and-block systems and other factory-made units are lifted into place. They are quick to install but need correct bearing and often a structural topping.

PCC versus RCC

PCC is plain cement concrete, and RCC is reinforced cement concrete.

  • PCC has no steel. It is strong in compression but weak in tension, so it suits blinding layers, bedding, non-structural fills and light-duty slabs on firm ground.
  • RCC contains steel bars or mesh to take tension. For beams, suspended slabs and anything carrying significant bending loads, RCC is the one to use. In that sense RCC is the stronger option for structural purposes.

Concrete strength grades

Concrete is graded by its compressive strength at 28 days. Higher numbers mean stronger concrete, so 25 MPa concrete is stronger than 20 MPa. Grades such as M20 or M25 are used in some countries, and the UK and Europe use classes such as C25/30 (cylinder strength / cube strength). The ratios for nominal mixes and a grade table are in concrete mixes for driveways, paths and pervious paving. Reinforced structural slabs normally require a specified grade chosen by the designer. For the ratio question, remember that stronger grades usually need a designed mix, not a fixed volume ratio.

What is the cheapest way to reinforce concrete?

For a typical ground-bearing slab, welded steel mesh is often the simplest and most economical option, as it comes in sheets and is quick to lay. Loose rebar can also be cost-effective depending on the layout and local prices. Fibre additives can help control shrinkage cracks but are not a direct substitute for steel where the design calls for steel. Cheaper does not mean suitable: reinforcement must match the slab’s load and span. Skipping it on a slab that needs it is a false economy.

Which type matters for a DIY project?

Most garden and home projects are ground-bearing slabs, so the key things are the base, the thickness, joints and curing. Suspended slabs, raft foundations and anything supporting walls, floors above or vehicles heavier than a car should be designed and checked by a professional. For help with joints in an on-grade slab, see control joint spacing in concrete slabs.

The complete guide to concrete slabs

How to Lay a Concrete Slab: Base, Mix and Pouring in Sections
Read the guide

Keep exploring

Guides from other topics

All topics →