Short answer
Yes, a new layer of concrete can be poured over an existing slab, but only if the old slab is in reasonable condition and you accept some trade-offs. If the old slab is cracked, moving, or sitting on poor ground, a new layer on top will usually inherit the same problems. In that case, removing the slab and starting again, using a proper base, is often the better route. See how to lay a concrete slab for what that involves.
When it works and when it doesn’t
An overlay is more likely to succeed when:
- The existing slab is structurally sound, with no significant heave, settlement or rocking.
- Cracks are fine, stable hairline cracks rather than wide or displaced ones.
- The surface is stained, worn, pitted or simply ugly.
- You have enough height to add thickness without causing problems at doors, drains or the damp-proof course.
It is a poor idea when:
- The slab has settled or tilts and the ground below is still moving.
- There are wide or uneven cracks, where one side sits higher than the other.
- Water drains toward a building and raising the level would make that worse.
- The old surface is crumbling or delaminating.
Bonded versus unbonded
There are two broad approaches.
Bonded overlay. The new layer is meant to stick to the old slab so they act as one. This needs a thoroughly cleaned and roughened surface, and usually a bonding agent or slurry coat, with the new layer placed while that is still active. Bonded overlays can be relatively thin, but they depend entirely on a good bond. If the bond fails, the layer can lift, sound hollow and crack.
Unbonded overlay. The new layer is separated from the old slab, commonly by a polythene sheet or similar slip layer, so it behaves as a new slab sitting on the old one. It needs to be thicker, typically at least the thickness you would use for a new slab of that type (for example, around 100 mm or 4 in for a patio), and it isn’t affected if the old surface can’t bond. Movement in the old slab is less likely to telegraph up, but joints in the old slab may still show through.
If you are unsure, an unbonded layer at normal slab thickness is usually the more forgiving option, provided you can afford the extra height.
Preparing the old slab
- Check for movement, rocking and voids. Tap the surface and listen for hollow sounds.
- Repair large cracks and loose areas first.
- Remove oil, grease, paint, sealer and loose or crumbling concrete. A pressure washer helps, and mechanical scabbling or grinding may be needed for a bonded layer.
- Make sure drainage still works after the new level goes down.
- Form up the edges, since the new layer will otherwise slump off the sides.
- Where the slab meets a house, keep the finished surface below the damp-proof course. About 150 mm is the usual guidance for paving.
Thickness, reinforcement and joints
Very thin layers are fragile and tend to crack or lift, particularly where they are unbonded. For anything that carries vehicles, think about the same thickness and reinforcement as a new slab. See rebar or wire mesh in a concrete slab.
It helps to cut or form joints in the new layer directly above joints and cracks in the old slab, since movement in the old slab otherwise reflects up as a crack. More on spacing in control joint spacing in concrete slabs.
Disadvantages
- Cracks can reflect through, especially with a thin or bonded layer.
- Delamination. A poorly bonded overlay may debond and lift.
- Raised level. Doors, thresholds, gullies and damp-proofing can be affected.
- Extra weight and cost compared with simple surface treatments.
- It hides, but does not fix, problems in the base underneath.
What does it cost?
Costs vary widely with location, access, thickness and whether you need a pump or ready-mix. As a rough indication of what drives cost for something like a large garage floor: the volume of concrete (area × thickness), the preparation, any reinforcement, labour, and short-load fees for small deliveries. Get a few written quotes and compare them with the cost of removing the old slab, which can sometimes be competitive with an overlay once preparation is included. If you are comparing DIY and bought-in options, see is it cheaper to mix your own concrete.
Cheaper ways to cover a concrete patio
If the aim is mainly cosmetic, a full pour is often more than you need. Alternatives include:
- Cleaning, repairing and sealing or painting the surface.
- A thin polymer-modified resurfacer designed for worn concrete, applied to the manufacturer’s directions.
- Laying paving slabs or tiles on a suitable bed, which also lets you change the level and appearance.
- Decking or other raised finishes over a sound base.
Each has its own preparation and limits, so check the product instructions and suitability for external use.