Concrete Repair

Can I resurface my concrete?

Yes, if the slab is structurally sound. Learn when concrete resurfacing works, when to replace instead, the basic steps, and the mistakes that make overlays fail.

On this page
  1. Short answer: usually yes, if the slab is sound
  2. When resurfacing works
  3. When to replace instead
  4. How to resurface concrete
  5. Common mistakes
  6. How long it lasts

Short answer: usually yes, if the slab is sound

Concrete can usually be resurfaced by applying a thin cement-based or polymer-modified overlay over the existing slab. It suits surface problems such as pitting, scaling, light spalling, stains, discoloration and minor cracks. It isn’t a fix for a slab that is moving, sinking or breaking up.

When resurfacing works

Resurfacing is a good candidate when:

  • The slab is firmly supported and in one piece.
  • Damage is mostly at the surface: scaling, pitting, flaking, rough or stained areas.
  • Cracks are fine and stable.
  • The slab is dry enough and clean enough to bond with.
  • You want a refreshed look without the cost of replacing the slab.

When to replace instead

Overlays won’t hold up on slabs that are:

  • Sinking, heaving, or shifting because of poor ground or tree roots.
  • Crumbling or soft through their depth.
  • Cracked with offsets, or with cracks that keep moving. They tend to reflect through the overlay.
  • Wet from below, since trapped moisture can push a coating off.

See is it cheaper to replace or repair concrete and how to fix a sunken concrete slab. If the slab is sound but you want a full new layer rather than a thin coat, see pouring concrete over an existing slab.

How to resurface concrete

Always follow the product’s instructions, since thickness, water, temperature limits and cure times differ.

  1. Clean the slab. Remove dirt, oil, grease, paint and sealer. A pressure washer helps. Oil often needs a degreaser.
  2. Profile the surface. Weak, flaking concrete must come off. Grinding, shot blasting or acid etching (per the product directions) gives the overlay something to grip. Rinse thoroughly after etching.
  3. Repair defects. Fill cracks and deeper holes first with a patch. See what to patch concrete with and repairing spalling concrete.
  4. Protect joints. Mask and keep control and expansion joints open, so they can still move. Covering them tends to lead to cracks over the joint.
  5. Dampen the slab. Most cement-based products want a damp surface with no standing water, but check the label.
  6. Mix and apply. Mix to the recommended consistency, then spread with a squeegee or trowel. Resurfacers are generally applied in thin layers, often in the range of about 1/16 to 1/4 inch, though products vary.
  7. Texture. For outdoor areas, a broom finish adds grip.
  8. Cure. Keep it out of direct sun and rain, and don’t walk or drive on it until the product says it’s ready.
  9. Seal if recommended. See the downsides of sealing concrete for the trade-offs.

Avoid applying in very hot, cold or windy conditions, or when rain is forecast.

Common mistakes

  • Skipping cleaning or leaving a layer of old sealer or laitance.
  • Applying over weak concrete.
  • Not fixing cracks and not understanding why they moved.
  • Covering joints.
  • Applying too thickly in one pass, or over-watering the mix.
  • Letting the surface dry out too quickly.

How long it lasts

It depends heavily on the product, the preparation, the traffic and the climate. Well-prepared overlays can last for years, but one applied over a poorly prepared slab may start peeling within a season. If the old slab is in poor condition, resurfacing only postpones the problem.

If cracks are the main problem, see our guide to concrete cracks.

The complete guide to concrete repair

Cracks in Concrete Slabs and Foundations: What's Acceptable and How to Fix Them
Read the guide

Keep exploring

Guides from other topics

All topics →