Concrete Repair

Waterproofing and Resurfacing Basement and Interior Brick Walls

How to find the moisture source, resurface a basement concrete wall, waterproof interior brick, and what waterproofing admixtures and paint can and can't do.

On this page
  1. Start by finding the water source
  2. Interior waterproofing vs. exterior fixes
  3. Resurfacing a concrete basement wall
  4. Waterproofing interior brick walls
  5. Waterproofing compounds and admixtures in concrete
  6. Should you paint basement walls?
  7. Vapor barriers and covering an interior brick wall
  8. The cheapest way to cover a basement concrete floor

Start by finding the water source

Interior waterproofing products treat symptoms. Before you buy anything, work out whether the moisture is coming through the wall, or is condensation, or comes from a leak.

A simple check: tape a square of plastic sheet (about 2 feet across) tightly to the wall, sealing all four edges, and leave it for a day or two. Moisture on the wall side of the plastic suggests water coming through the wall. Moisture on the room side suggests condensation from humid indoor air.

Common causes of real water entry are poor surface drainage, gutters that discharge near the wall, a high water table, or cracks and failed joints. Fixing these outside, such as regrading soil away from the house, extending downspouts and clearing gutters, often does more than anything applied indoors.

Interior waterproofing vs. exterior fixes

Interior coatings can reduce dampness and dusting from a damp wall, and are the practical option when you can’t dig outside. But they are generally not a substitute for managing water outside. If water pressure is significant, or there is active leaking, bring in a waterproofing specialist.

Resurfacing a concrete basement wall

A rough, flaking, crumbling or patchy wall can be resurfaced with a cement-based coating, often called a parge or masonry resurfacer.

  1. Remove loose material. Scrape and wire-brush off old paint, flaking coatings and crumbling surface. A wall that is crumbling from moisture needs the cause addressed.
  2. Clean and remove salts. White powder (efflorescence) should be brushed off. See removing efflorescence.
  3. Repair cracks and holes. Fill them with a suitable patch or hydraulic cement for active seepage. See what to patch concrete with and concrete block wall cracks.
  4. Dampen the wall. Cement-based coatings usually bond best to a damp, not wet, surface.
  5. Apply the coating in thin coats with a brush or trowel, following the product’s directions about thickness and recoat timing.
  6. Cure. Keep it damp, or follow the instructions, so it doesn’t dry too fast.

Check the product label; some are designed for interior walls and some are rated for negative-side (interior) water pressure, but their limits vary. For general resurfacing tips, see can I resurface my concrete.

Waterproofing interior brick walls

Can you waterproof brickwork? Yes, to a degree. Brick and mortar are porous, so how you treat them depends on the problem:

  • Fix the masonry first. Repoint crumbling mortar joints and replace cracked bricks. See patching a brick wall.
  • Clean. Remove loose paint, dirt and salts.
  • Choose the coating. Options include cement-based waterproofing coatings (which change the look of the brick), and clear penetrating masonry sealers (which keep the brick look). Breathable products let vapor through, while film-forming ones don’t and can trap moisture. For the trade-offs, see the downside of sealing concrete.
  • Test first. Try a small hidden patch.

If the wall is damp because water is coming through from outside, an interior sealer may blister or flake off. This is one reason the source matters.

Waterproofing compounds and admixtures in concrete

Waterproofing admixtures are added to concrete or mortar mixes to reduce water absorption or permeability. Types include crystalline admixtures, water-reducing admixtures that make a denser mix, and hydrophobic (water-repellent) additives. They’re mainly useful for new concrete or render, not as a cure for an existing leaking wall. Follow the manufacturer’s dosage, since overdosing can cause problems.

As for adding PVA: PVA (polyvinyl acetate) glue is sometimes added to mortar or slurry as a bonding aid. It can improve adhesion, but it isn’t generally regarded as making cement waterproof, and standard PVA can soften when it stays wet. For anything that must stay wet, use products made for the purpose.

Should you paint basement walls?

You can, but paint won’t stop water coming through the wall. Masonry waterproofing paints can reduce dampness from light moisture; ordinary wall paint on a damp wall tends to peel and bubble. Make sure the wall is clean and dry, and treat any efflorescence first. How long painted concrete lasts depends on the moisture level, the product, and the preparation, so there’s no reliable number.

Vapor barriers and covering an interior brick wall

If you want to cover brick with drywall, the question of vapor barriers depends on the climate, the wall construction and local building rules. A common approach is to leave an air gap or use furring strips and rigid insulation, but putting vapor barriers in the wrong place can trap moisture. Check with your local building authority or a building professional. If the brick is damp, deal with that first.

The cheapest way to cover a basement concrete floor

For a floor, the cheapest is often a concrete paint or a thin cement-based resurfacer. Both need a clean, sound slab. If the floor is damp, or moisture rises through it, coverings can fail or trap moisture.

The complete guide to concrete repair

Cracks in Concrete Slabs and Foundations: What's Acceptable and How to Fix Them
Read the guide

Keep exploring

Guides from other topics

All topics →