Concrete Repair

How to Fix a Sunken Concrete Slab: Mudjacking, Foam and Replacement

Why concrete slabs sink and how to fix them: compare mudjacking, polyurethane foam injection and replacement, plus what is realistic for DIY and how to fix drainage.

On this page
  1. Why slabs sink
  2. Your options at a glance
  3. Mudjacking
  4. Polyurethane foam
  5. Mudjacking vs. foam vs. replacement
  6. Can you DIY it?
  7. Fix the cause: drainage
  8. When to replace

Why slabs sink

A concrete slab is only as stable as the ground beneath it. Slabs usually sink because the support under them has gone or moved:

  • Poorly compacted fill under the slab settles over time (see how much gravel you need under a concrete slab).
  • Soil erosion and washout, often from downspouts discharging near the slab, poor grading or leaking pipes, which carry soil away and leave voids.
  • Soft or expansive soils that change volume with moisture.
  • Tree roots or removed trees, which change soil moisture.
  • Frost and thaw cycles in cold climates.

Before you pick a fix, work out why it sank. If water keeps washing out the soil, any repair is temporary. Sinking is often accompanied by cracks. See our guide to concrete cracks.

Your options at a glance

  1. Mudjacking (slabjacking). Pumping a cement-based slurry under the slab to lift it.
  2. Polyurethane foam injection. Injecting expanding foam under the slab.
  3. Replacement. Breaking out the slab, fixing the base, and pouring new concrete.
  4. Grinding or patching. For small height differences at joints and cracks, where the main concern is a trip hazard rather than the slab sinking.

Mudjacking

A contractor drills holes (commonly around 1–2 inches wide) through the slab and pumps in a mixture of soil, cement and water or a similar slurry. The slurry fills voids and pushes the slab back up. It’s been used for a long time, and is usually among the lower-priced lifting options. The slurry is heavy, so the added weight on soft soil can be a consideration, and the holes are larger than with foam. Because the work is done at a distance from the slab with a pump and hoses, it takes experience to lift evenly without cracking the slab.

Polyurethane foam

With foam, a contractor injects a two-part polyurethane foam through smaller holes. It expands to fill voids and lift the slab, then hardens quickly. Foam is lightweight and the small holes are less visible. It typically costs more than mudjacking, but is often presented as longer-lasting and better for areas with weak soils. Ask contractors about the product, warranty and experience.

Mudjacking vs. foam vs. replacement

Mudjacking Foam Replacement
Typical cost Usually lower than foam Often higher than mudjacking Often the highest overall, particularly with demolition
Hole size Larger Smaller Not applicable
Weight added More Very little New slab weight only
Best for Larger areas with enough support Areas where weight matters, or where a faster cure matters Slabs that are badly broken or have lost support
Fixes the cause? Fills voids, doesn’t fix drainage Fills voids, doesn’t fix drainage Allows the base to be redone

Prices differ a lot by region and contractor, so get several quotes. Lifting only works if the slab itself is intact. If it’s heavily cracked or crumbling, replacement is more likely to be worthwhile. See is it cheaper to replace or repair concrete.

Can you DIY it?

Raising a slab needs specialist pumps and experience, and doing it wrong can crack the slab or make things worse, so most homeowners hire a professional. DIY kits for foam do exist, but results depend on skill. What is realistic for homeowners:

  • Fixing the drainage that caused the problem.
  • Grinding down a small lip at a crack to remove a trip hazard.
  • Filling small voids near edges.
  • Patching or smoothing the edge with a suitable repair product. See what to patch concrete with.
  • Replacing a small slab, such as a step landing or walkway section, if you’re comfortable with concrete work.

Fix the cause: drainage

  • Extend downspouts so roof water is discharged well away from slabs.
  • Grade soil so it slopes away from the slab.
  • Fix leaking pipes or irrigation near the slab.
  • Seal gaps along the slab edge where water can run in.
  • Keep gutters clean.

When to replace

Replacement tends to be the better choice if the slab is broken into pieces, deeply cracked, much thinner than it should be, or the soil underneath is unstable enough that lifting wouldn’t last. If it’s a garage slab, see repairing or replacing a damaged garage floor. If the sunken slab is near the house and you see cracks in walls or doors that stick, have a structural engineer look at it.

The complete guide to concrete repair

Cracks in Concrete Slabs and Foundations: What's Acceptable and How to Fix Them
Read the guide

Keep exploring

Guides from other topics

All topics →