Concrete Repair

How to Repair Broken and Crumbling Concrete Step Edges

Step-by-step guide to rebuilding a broken concrete step corner or edge with repair mortar and a form, plus when crumbling steps need replacing.

On this page
  1. Repair or replace the steps?
  2. What you’ll need
  3. Step by step: rebuilding a broken corner
  4. Repairing crumbling surfaces and small chips
  5. Choosing a repair product
  6. Safety and stopping a repeat

Repair or replace the steps?

Step edges and corners take the most abuse: impact, water that runs off them, de-icing salts and freeze-thaw. Chipped or crumbling corners can often be rebuilt. Replacement is worth considering when:

  • Crumbling is widespread across treads and risers, not just the edges.
  • The steps have settled, tilted, or pulled away from the house.
  • There are wide or growing cracks, or large pieces that have broken off.
  • The concrete is soft and powdery throughout.
  • Risers and treads are uneven enough to be a trip hazard.

For the cost picture, see is it cheaper to replace or repair concrete. If the steps are sinking, see fixing a sunken concrete slab. If you rebuild them, see concrete mix ratios for steps.

What you’ll need

  • Hammer and cold chisel, or an angle grinder with a masonry wheel
  • Wire brush, stiff broom and a vacuum
  • Eye protection, gloves and a dust mask
  • A suitable repair mortar for edges and vertical surfaces, ideally non-sag (see below)
  • Bonding agent, if the repair product calls for one
  • Form boards or a piece of wood, clamps or bricks to hold it
  • Mixing bucket, margin trowel, and a finishing trowel or edger
  • Release agent or plastic sheeting for the form

Step by step: rebuilding a broken corner

  1. Clean out the damage. Chisel back to sound concrete. Remove all loose, cracked and crumbling material. A clean, firm edge gives the repair something to hold on to. Tap-test the surrounding area, and keep removing any concrete that sounds hollow.
  2. Make the edge of the repair definite. Rather than feathering to nothing, many repair products work better when the perimeter is chiseled to a small vertical edge, as per the manufacturer’s recommendations, since feather edges tend to chip off.
  3. Clean thoroughly. Brush and vacuum out dust and rinse the area if the product allows. Remove oil or grease.
  4. Set the form. Hold a board against the step face where the corner used to be, flush with where the finished surface should be. Use a release agent or plastic on the board so the repair doesn’t stick to it.
  5. Prepare the surface. Dampen the old concrete (no puddles) or apply a bonding agent, whichever the product directs.
  6. Mix the repair mortar. Mix a small batch to the thickness recommended, usually stiff enough to hold its shape.
  7. Pack it in. Press the mortar firmly into the cavity, working it against the old concrete and into the corners, and fill in layers if the repair is deep.
  8. Finish. Strike off level with the form and trowel smooth, then use an edging tool to round the corner if the original was rounded. Match the surface texture, such as a light broom finish for grip.
  9. Remove the form when the mortar has firmed up enough to hold its shape, usually after a short wait that depends on the product, and tidy the edge.
  10. Cure. Keep it damp or covered if directed and protect it from frost, hot sun and rain. Keep off it until the product says it is safe.

Repairing crumbling surfaces and small chips

For a crumbling tread rather than a broken corner, remove the weak layer, clean, and apply a repair mortar or thin resurfacer, as described in repairing spalling concrete and can I resurface my concrete. For small chips, a vinyl-modified patch may do.

Choosing a repair product

Look for a product rated for vertical or edge repairs and exterior use, with a maximum thickness that suits your damage. For small corners, a polymer-modified repair mortar is a common choice, and quick-setting products are helpful for shaped repairs, though they leave less working time. See what to patch concrete with for a comparison.

Safety and stopping a repeat

Steps are a trip-and-fall risk, so make sure all treads and risers are even and stable before you use them again. Handrail and riser-height requirements vary by region, so check your local code if you are making bigger changes.

To reduce future damage:

The complete guide to concrete repair

Cracks in Concrete Slabs and Foundations: What's Acceptable and How to Fix Them
Read the guide

Keep exploring

Guides from other topics

All topics →