Patios and Paving

Laying Paving Slabs on an Existing Concrete Base

Can you lay paving slabs on an existing concrete base? How to check the slab, set levels and fall, choose a mortar or sand bed, and handle joints.

On this page
  1. Can you lay slabs on existing concrete?
  2. Check the concrete first
  3. Check the levels and the fall
  4. Mortar bed or sand bed?
  5. Step-by-step
  6. Movement joints
  7. How soon after pouring new concrete?
  8. Joining a new slab to an existing one
  9. Cheaper ways to cover a concrete patio
  10. Mistakes to avoid
  11. Can pavers go over a concrete slab?

Can you lay slabs on existing concrete?

Often yes. A sound, stable concrete slab can make a good base for paving slabs, and it saves you the digging and sub-base work. The catch is that the concrete needs to be in good condition, and the extra height and drainage need thought. If the concrete is cracked, sunken or moving, paving over it usually just carries those problems up through the new surface.

Check the concrete first

If the slab is unstable, it is generally better to break it out and build a proper sub-base. See how deep the sub-base should be for a patio.

Check the levels and the fall

Adding a bedding layer and slabs raises the finished surface. As a rough guide, allow the mortar bed (commonly 30 to 40 mm) plus the thickness of the slab. Check the effect on:

  • Door thresholds and any step down from the house.
  • The damp-proof course (DPC), if your house has one. In the UK, paving is generally recommended to sit well below the DPC, often quoted as at least 150 mm. Raising the surface can break that rule, so check before you start.
  • Drainage. Water should run away from the house. If the existing slab has little or no fall, you can build a gentle fall into a thicker bedding layer, but there are limits. See what slope a patio should have for drainage.

Also check whether water will be trapped under the new surface. Some installers drill small drainage holes in large slabs so water can escape, and a sand bed is more likely to hold water than a mortar bed.

Mortar bed or sand bed?

On concrete, a full mortar bed is the more usual approach. It bonds to the concrete and holds the slabs firmly. A sand bed on top of concrete is possible in some cases, but it has no drainage path unless you provide one, and the sand can wash out at the edges. For more on this, see whether you can lay patio slabs on sand or need a mortar bed.

A typical mix is sharp sand and cement mixed damp, in a ratio of roughly 4:1 to 6:1, as described in our mortar mix guide for patio slabs. Many installers prime the existing concrete first with a bonding primer or a brushed slurry coat so the mortar grips. Follow the product’s instructions.

Step-by-step

  1. Clean the concrete and repair any loose or crumbling areas.
  2. Set out string lines at the finished height, allowing for the fall.
  3. Prime the concrete if you are using a bonding primer or slurry.
  4. Trowel on a full bed of mortar, slightly proud of the final level.
  5. Prime the back of each slab if the manufacturer recommends it (common with porcelain).
  6. Lay the slab, tap it down with a rubber mallet to level, and keep joints even.
  7. Leave to set before pointing. See what to use to fill gaps between paving slabs.

Movement joints

Concrete slabs often have joints cut or formed into them to allow for movement. If you tile or pave over a movement joint with rigid mortar, the new surface can crack along that line. A common approach is to continue the existing joint through the new bed and slabs with a flexible filler. Check the guidance for your slab type.

How soon after pouring new concrete?

If the concrete is new, give it time. Fresh concrete shrinks as it cures, and bedding mortar on top can crack if that shrinkage is still happening. Twenty-eight days is the usual benchmark for full strength, and many installers wait at least a good number of days before paving over it. If in doubt, wait longer.

Joining a new slab to an existing one

If you are extending a concrete slab rather than covering it, new concrete is generally best separated from the old by an expansion or isolation joint, so the two can move independently. Where a structural tie is needed, rebar dowels can be drilled and bonded into the old slab. For anything load-bearing, get professional advice.

Cheaper ways to cover a concrete patio

If the aim is simply to improve the look, slabs may not be the cheapest option. Alternatives people use include:

  • Concrete paint or stain, or a resurfacing product, for a tired but sound surface.
  • Interlocking outdoor tiles that click together.
  • Large outdoor rugs for a quick, reversible change.

Paving slabs on a mortar bed give the most durable result but cost more in materials and time.

Mistakes to avoid

  • Laying over a cracked or moving slab.
  • Ignoring the DPC and threshold heights.
  • Using a mortar that is too wet.
  • Skipping the movement joints.

Our guide to common mistakes when laying pavers covers more of these.

Can pavers go over a concrete slab?

Small interlocking pavers can also be installed over a sound concrete slab, usually on a thin setting bed or mortar, with an edge restraint and attention to drainage. See interlocking concrete pavers for how those systems normally work.

The complete guide to patios and paving

Best Mortar Mix for Laying Patio Slabs
Read the guide

Keep exploring

Guides from other topics

All topics →