Patios and Paving

What to use to fill in gaps between paving slabs?

What to use to fill gaps between paving slabs: polymeric sand, resin jointing compound, sand and cement mortar, grout or kiln-dried sand, and how to choose.

On this page
  1. Short answer
  2. Start with how the slabs were laid
  3. The main options
  4. Choosing by joint width
  5. Prep and weather
  6. Stopping weeds
  7. Common mistakes

Short answer

The common choices for filling gaps between paving slabs are polymeric sand, resin jointing compound, sand-and-cement mortar, a specialist patio or porcelain grout, kiln-dried sand, and for wide decorative gaps, gravel or turf. The right one depends on how the slabs were laid, how wide the joints are, and the slab material.

Start with how the slabs were laid

  • Slabs on a mortar bed (rigid): A rigid filler such as mortar, grout or a resin compound is suited to this. See our mortar mix guide for how these are usually laid.
  • Slabs or pavers on a sand bed (flexible): A flexible or loose filler such as kiln-dried sand or polymeric sand copes better with slight movement. Rigid mortar in a flexible surface tends to crack. For more on how these systems work, see interlocking concrete pavers.

The main options

Polymeric sand

Fine sand mixed with binders that harden when lightly wetted. It resists washout and discourages weeds and insects, and is widely used with concrete pavers and slabs. It needs a dry surface, a compacted, full joint, and careful watering. Too much water can wash the binder out, and residue left on the surface can leave a haze. Follow the label for the joint width it can handle, often around 1 inch (25 mm) or less. Do not use it on permeable pavers, as it blocks drainage.

Resin jointing compound

A mix of sand and resin, sold pre-mixed or in two parts, that cures hard but is a little less brittle than mortar. It resists weeds well when packed properly, and it costs more than sand or mortar. Many are applied by brushing or by a gun.

Sand-and-cement mortar

A traditional filler that is cheap and durable in wider joints. Mixes of around 3:1 to 4:1 sand to cement are commonly used, and a drier, crumbly mix is generally easier to keep off the slab faces. It needs careful cleaning, as cement can stain porous slabs. Protect the surface, work small areas, and wipe off smears promptly.

Specialist patio or porcelain grout

Porcelain is dense and non-porous, so standard sand or mortar may not bond or fit well. Many porcelain suppliers recommend a specific slab grout or jointing compound. Use what the supplier advises.

Kiln-dried sand or joint grit

Best for narrow joints, or traditional natural stone laid on a flexible bed, where you want a permeable, non-hardening fill. It washes out more easily and needs topping up over time.

Gravel or turf

For wide decorative gaps, stepping-stone paths and driveway strips, gravel or turf improves drainage and softens the look. These are not suitable for narrow joints.

Choosing by joint width

Joint width Commonly used fillers
Narrow (a few mm) Kiln-dried sand, polymeric sand, specialist grout
Medium (about 5–10 mm) Polymeric sand, resin compound, mortar
Wide (over about 10 mm) Mortar, resin compound, gravel or turf

These bands are rough guides. Check the product for its own limits.

Prep and weather

  • Clear out old filler, moss and weeds. Take joints back to a firm depth of a few centimetres for mortar, so it has something to grip.
  • Brush and let the slabs dry thoroughly before using polymeric sand or resin.
  • Avoid rain, frost or very hot sun. Many sands and mortars need dry conditions and a minimum temperature to set.
  • Fill the joints completely, but keep material slightly below the surface.

Stopping weeds

Weeds usually come from seeds landing in loose joint material, or from growth beneath the slabs. A hardening filler helps. If the slabs sit on weeds that are growing up from below, no joint filler fully solves it, and relaying may be needed. See common mistakes to avoid when laying pavers for the base problems that lead to this.

Common mistakes

  • Using rigid mortar on slabs laid on sand.
  • Pointing too soon, before the bedding has set.
  • Over-wetting polymeric sand.
  • Leaving mortar or resin residue on porous slabs.

The complete guide to patios and paving

Best Mortar Mix for Laying Patio Slabs
Read the guide

Keep exploring

Guides from other topics

All topics →