What interlocking concrete pavers are
Interlocking concrete pavers are small, factory-made concrete units laid on a compacted base and a thin layer of bedding sand, with sand swept into the joints. Unlike a poured slab or mortared paving, the surface is flexible. The units lock together through friction in the joints and the edge restraint around the perimeter, so the whole surface can move slightly with the ground without cracking. If one unit is damaged or stained, it can generally be lifted out and replaced.
What type of concrete is used for pavers?
Pavers are made in a factory from a low-water, high-strength concrete mix, compressed and vibrated in moulds. That process produces a dense, consistent unit that is stronger than ordinary site-mixed concrete. Standards in many countries set minimum strength and freeze-thaw performance. For example, US pavers are commonly specified to ASTM C936, and in Europe to BS EN 1338 for concrete paving blocks. Check that the product you buy states compliance with a relevant standard.
How the system works
From the bottom up:
- Compacted soil (the sub-grade).
- Compacted base of crushed stone or similar material. Many guides suggest roughly 100 to 150 mm (4 to 6 inches) for patios and paths, with more for driveways or soft ground. See how deep the sub-base should be for a patio.
- Bedding layer of sand, commonly around 25 mm (1 inch), screeded level. It is not meant to be thick.
- Pavers, laid tight with narrow joints.
- Joint sand swept in and compacted.
- Edge restraint around the perimeter to stop the pavers spreading.
Interlocking pavers are laid on sand rather than mortar. This differs from slabs, where a mortar bed is common; see the mortar mix guide for patio slabs and our comparison in can you lay patio slabs on sand or do you need a mortar bed.
Choosing thickness and pattern
- Thickness: Pavers around 50 to 60 mm are common for pedestrian areas, and thicker units (around 60 to 80 mm) are used where vehicles will drive. Check the manufacturer’s guidance for the load.
- Pattern: Herringbone is generally regarded as the pattern that interlocks best and resists movement, which is why it is often recommended for driveways. Running bond and stack bond are fine for foot traffic. Stack bond has less interlock.
- Colour: Buy all you need at once and mix from several pallets as you lay, so batch differences blend in.
How to lay interlocking pavers
- Mark out the area and excavate to the depth you need for base, sand and paver.
- Compact the sub-grade, adding geotextile fabric if the soil is soft or clay-heavy.
- Add the base in layers, compacting each one with a plate compactor. Check the fall for drainage; see what slope a patio should have.
- Screed the bedding sand using guide rails and a straight board. Do not walk on it afterwards.
- Lay the pavers from a straight edge, working outward, and keep your pattern aligned with string lines.
- Cut edge pavers with a masonry saw or splitter. Wear eye, ear and dust protection, and cut wet or with dust extraction where you can, as masonry dust is harmful to breathe.
- Install edge restraints and fix them firmly.
- Compact the surface with a plate compactor fitted with a protective pad.
- Sweep in joint sand and compact again, repeating until the joints are full.
Joint sand
Joints are usually filled with fine, dry sand, or with polymeric sand that hardens when it is activated with water, which helps resist weeds and washout. Follow the product instructions carefully, as it needs dry conditions and can leave a hazy film if it is left on the surface. Not every paver system suits polymeric sand, so check first, and do not use it on permeable pavers. For a wider look at joint options, see what to use to fill gaps between paving slabs.
How many pavers are on a pallet?
It varies widely with the size and thickness of the unit and the supplier. Most are sold by coverage, such as square feet or square metres per pallet, rather than a fixed number of bricks. Check the pallet’s labelled coverage, and order a little extra for cuts and breakages, commonly around 5 to 10 percent.
Can you put pavers over a cement slab?
It can be done if the slab is sound and stable. The usual considerations are the added height, drainage so water does not collect under the sand, and holding the edges firmly. Some installers use a thin sand bed or a mortar bed. See laying paving slabs on an existing concrete base.
Can you make your own?
You can cast pavers at home in moulds, and it is a legitimate hobby project. Home-cast units are generally not as dense or consistent as factory pavers, so they suit decorative or light-use areas better than driveways.
Are they cheaper than pouring concrete?
Usually the upfront cost is higher for pavers than for plain poured concrete. See are concrete pavers cheaper than pouring concrete for the cost comparison.
Mistakes to avoid
- A thin or poorly compacted base.
- Laying the sand bed too thick, or compacting it before laying.
- No edge restraint.
- Using the wrong sand.
See common mistakes to avoid when laying pavers for more.