The short answer
For kerbs and edging stones, you generally need a bed of concrete under the unit and a “haunch” of concrete behind it. A general-purpose mix of about 1 part cement, 2 parts sharp sand and 4 parts 20 mm aggregate by volume is commonly used, as are bagged general-purpose concrete or fence-post mixes. Brick edging that is mortared together uses a sand-and-cement mortar instead. Check the product instructions for the mix you buy.
Bed and haunch
- Bed: a layer of concrete the unit sits on. Many guides suggest something in the region of 100 mm deep, a little wider than the kerb.
- Haunch: a wedge or block of concrete behind (and sometimes in front of) the kerb, holding it upright against sideways pressure. It is often taken up to around half the kerb’s height, sometimes more.
The bed keeps the kerb level and supported. The haunch stops it tipping or being pushed outward, for example by a compacted paving base behind it.
Concrete mix for kerbs
Typical mixes (by volume):
- About 1 : 2 : 4 cement to sharp sand to 20 mm aggregate, or
- About 1 : 5 cement to all-in ballast, or
- Bagged general-purpose concrete mix.
Mix it fairly stiff, as a wet mix is weaker and can slump under the kerb. Twenty-millimetre aggregate is common for this sort of work, and 10 mm aggregate is used where a section is thin or a smoother finish is wanted. In areas that see hard frosts, or where vehicles will run along the kerb, ask your supplier about a stronger or air-entrained mix.
Mortar for brick edging
If you are laying bricks on edge or on end as an edging, a typical approach is:
- A concrete bed and haunch to hold the line, then
- Bricks set into a bed of mortar made from building sand and general-purpose cement (often about 4:1 to 6:1 by volume, with a plasticiser), or
- Bricks set directly into a concrete bed while it is still workable.
Use frost-resistant bricks suitable for exposed paving. Ordinary house bricks may crumble outdoors in cold wet weather. Cement used to lay bricks is normally ordinary Portland cement, though masonry cements and ready-mixed mortars are also used.
How much concrete to lay a kerb?
Work out the cross-section and multiply by length. A worked example for one metre of kerb:
- Bed: 150 mm wide × 100 mm deep × 1 m = 0.015 m³
- Haunch: 100 mm wide × 100 mm high × 1 m = 0.010 m³
- Total: about 0.025 m³ per metre
For 20 m of kerb, that is about 0.5 m³, plus roughly 10 percent for waste. Change the dimensions to suit your own kerb and ground.
How much mortar for 1000 bricks?
It depends on the joint thickness, brick size and what you are building. A figure often quoted for standard bricks in a wall is in the region of half a cubic metre of mortar per thousand, but edging bricks are laid differently and usually use much less per brick. Work from your own bed and joint dimensions, or buy a little extra and keep any surplus dry.
Do edging stones need cement?
Usually yes, if you want them to stay put. Loose-laid stones can shift, tilt or be pushed outward by the paving. A concrete bed and haunch is the common approach for kerbs and for edging next to a driveway or a patio. For light-duty garden borders, some people set edging stones firmly into compacted soil or sand without cement, which is fine where nothing is pushing against them. Paving that relies on an edge to stop it spreading, such as interlocking concrete pavers, needs a firm restraint.
Can you use Quikrete for curbing?
Bagged concrete from brands such as Quikrete can be used for a bed and haunch under edging and curbing units. For a continuous cast-in-place curb you form it yourself, check the specific product, because some are made for other uses, and follow the label for mixing and curing. Bagged mix costs more than mixing from raw materials, but it is convenient for small jobs.
What is “poor man’s concrete”?
There is no standard definition. People use the phrase for various cheap homemade mixes, often cement and sand with little or no coarse aggregate, or a mix with extra sand to stretch the cement. Such mixes are generally weaker and more likely to crack. For anything supporting a kerb, stick to a proper concrete mix.
Steps
- Set out a string line at the finished height.
- Excavate a trench for the bed and haunch, and compact the base.
- Lay a bed of concrete and place the kerb or bricks, tapping down to the string line.
- Check the level and fall. See what slope a patio should have for drainage.
- Add the haunch behind, trowelled to a slope so water runs away.
- Keep off it, and protect it from rain and frost while it sets. Fresh edging can be disturbed by early paving, so allow it to firm before laying beside it.
For the mortar under the slabs themselves, see our mortar mix guide for patio slabs.